亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo hydraulic cylinder Sold to Azerbaijan

Release time:2023-11-12 15:27:32 Hits: Current position: Home > News

This article mainly introduces:

Azerbaijan hydraulic cylinder,servo hydraulic cylinder manufacturer,servo hydraulic cylinder

Azerbaijan servo hydraulic cylinder

(Azerbaijan servo hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

servo hydraulic cylinder are widely used in Azerbaijan,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed servo hydraulic cylinder for customers from Azerbaijan.

Introduction to servo hydraulic cylinder:

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the servo hydraulic cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

The definition of the minimum stable speed refers to the minimum movement speed of the servo hydraulic cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the servo hydraulic cylinder that undertakes different work has different requirements for the minimum stable speed.

After chrome plating of the piston rod of the servo hydraulic cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

The difference between the integral servo hydraulic cylinder and the split servo hydraulic cylinder: The integral servo hydraulic cylinder and the split servo hydraulic cylinder in the servo hydraulic cylinder are two different servo hydraulic cylinders, and they are very different. The whole servo hydraulic cylinder, which is cast in one body, is not prone to problems such as oil leakage; The split servo hydraulic cylinder is welded twice, so if it is not handled well at the welding, it is prone to problems such as oil leakage and servo hydraulic cylinder damage. Therefore, it is obvious that the answer to this question is for difference.

Answers to some questions about servo hydraulic cylinder:

How to disassemble the cylinder?
Generally speaking, it is not difficult to disassemble the hydraulic cylinder, as long as you are careful, but you often encounter some small trouble in the disassembly process, because the disassembly process is not correct. In fact, this can be avoided, as long as you follow below points. 1. Before removing the hydraulic cylinder, the hydraulic circuit should be relieved of pressure, otherwise, when the oil pipe connected with the cylinder is loosened, the high-pressure oil in the circuit will be rapidly ejected. When the hydraulic pressure comes back, the handwheel or pressure regulating screw at the relief valve should be loosened first, so that the pressure oil is unloaded, and then the power supply or power source is cut off, so that the hydraulic device stops running. 2. Disassembly should prevent damage to the top thread of the piston rod, the oil thread and the chrome layer on the piston rod surface.

Does the excavator use a hydraulic cylinder?
First, construction machinery is generally a hydraulic cylinder. Second, hydraulic transmission equipment is usually composed of four components, power, execution, control and auxiliary. And the hydraulic cylinder as a linear reciprocating motion or less than 360. Reciprocating motion of the hydraulic mechanism, simple structure, reliable work, is also widely used in the hydraulic system of the main actuator, it is the prime mover in the form of mechanical energy to drive the hydraulic pump produced by the liquid pressure energy, and then can be directly driven load for reciprocating movement or less than 360.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日本五十路六十路无码在线精品| 美女肏屄久久| 鸡吧插在线观看| 日本有吗在线观看中文字幕在线观看 | 大鸡吧久草免费在线| 欧美日韩视频另类| 大香蕉在日本视频网| 鸡巴不卡逼视频| 日本超级碰免费| 日韩淫淫| 黑人大鸡巴久久久密乳| 国产 日韩 欧美高清| 欧美在线观看高清| 人人操天天舔| 日本麻豆一区二区| 国产精品一区二区午夜香蕉| 国产成人处女Av一区二区| 91无码精品一区二| 日韩免费在线观看视频| 操美女的逼逼的视频| 什么视频可以免费看大鸡巴| 偷拍偷拍福利免费观看| 大几把艹嫩逼视频| 大吊后操插逼视频| 日韩精品有码无码| 狼人香蕉狠狠| 五五月综合婷婷| av在线导航网| 福利视频女| 大鸡巴插入美女阴道视频| 青青热免费视频在线观看| 深爱五月在线激情AV| 日韩人妻骚| 亚洲影院第一区第二区| 激情小说亚洲精品| 有爽有色的黄片| 操B精品| 国产少妇深喉| 午夜福利网站入口| 蜜桃网址鸡巴| 亚欧洲精品无码视频|