亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

lifting platform cylinder Sold to Switzerland

Release time:2023-11-12 15:28:53 Hits: Current position: Home > News

This article mainly introduces:

Switzerland hydraulic cylinder,lifting platform cylinder manufacturer,lifting platform cylinder

Switzerland lifting platform cylinder

(Switzerland lifting platform cylinder,produced by Hengyu Hydraulic Co., Ltd)

lifting platform cylinder are widely used in Switzerland,because of no need for deceleration device,long service life,smooth movement.So our company has designed lifting platform cylinder for customers from Switzerland.

Introduction to lifting platform cylinder:

If the piston rod and lifting platform cylinder are stuck or the lifting platform cylinder is blocked, at this time, no matter how to operate, the lifting platform cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the lifting platform cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

In the process of using the lifting platform cylinder, sometimes such a problem will occur, the lifting platform cylinder can not act immediately after the instruction of the lifting platform cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil lifting platform cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

The machining accuracy of the lifting platform cylinder depends on the level of equipment, production technology and testing means. lifting platform cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

lifting platform cylinder abnormal sound, hysteresis phenomenon cause and elimination method: the piston rod is extended with abnormal sound and hysteresis, if the lifting platform cylinder is placed for a period of time, the lifting platform cylinder may enter the air, and the movement can be normal after dozens of repeated movements. If it still cannot be eliminated, check whether the load is aligned with the axis of the piston rod; Retracted piston rod installation helps to align the load with the piston rod. If the flow is unstable, it will also lead to abnormal movement of the piston rod. Check the relevant components of the hydraulic system.

Answers to some questions about lifting platform cylinder:

Can pneumatic cylinder be used as hydraulic cylinder?
The pneumatic cylinder can only be used for pressure below 1MPA, and if it is used for hydraulic, the pressure should be under 1MPA, which may not meet the strength requirements. And the seals should use fluorine rubber to avoid corrosion. But pneumatic cylinder used as hydraulic cylinder is not whimsical, in fact, there is such a use. The pneumatic system has a natural defect, that is, the speed is unstable, especially in the case of low speed. The hydraulic pressure is very stable, if you do not want to buy a set of hydraulic system, while the strength of the cylinder is not large, you can use compressed air to push the hydraulic oil, with hydraulic oil to drive the cylinder, The force is the same as compressed air, but very smooth.

What size of hydraulic cylinder is needed for 200 tons pressure? The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate by the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the pressure level P (unit MPa) when working, then the thrust of the cylinder F push =3.14*R*R*P (unit N) the pull of the cylinder F pull =3.14* (R* R-R *R) *P (unit N) 100 tons of the cylinder, System pressure 16Mpa.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
想要大鸡巴操骚逼调教视频| 欧美日韩一区青青艹| 成人午夜免费性副利视频| 一级片黄片骚逼骚逼骚逼逼| 野外白虎少妇| 日韩黄色mv无码视频| 台湾妹视频在线观看| 极品五月天一区二区三区| 美女116免费午夜视频| 大学生高潮一级A片| 五月丁香色综合久久蜜臀AV| 久久人妻夜夜做天天爽| 熟妇 性视频| 大鸡巴疯狂草逼激情视频| 啊啊嗯…啊…在线观看| 午夜鲁鲁久久| 逼操视频了吗你| 精品少妇2| 台湾佬久久中文娱乐网| 在线浏览污麻豆| 亚洲天堂是熟女| 超大机巴操小逼高清视频| 上海老女人嗷嗷叫AV| 伊人色综合久久天天五月婷| 歐美福利網| 美女护士视屏国产| 人妻 少妇 制服 另类| 经典伊人老司机| 91人妻在线播放| 午夜免费AV电影| 亚洲区熟女一区二区| 日日不卡av| 五月婷Av在线| 大香蕉高清在线一区二区三区| 91n免费处女在线破视频+进...| 国产成人在线看一区二区苹果视频| 日本六十路完整视频| 嗯啊嗯哪艹| 韩国中学生激情性爱网| 中文字幕色制服诱惑| 一区二区三区不卡中文字幕|