亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

flange type cylinder Sold to Spain

Release time:2023-11-12 15:29:56 Hits: Current position: Home > News

This article mainly introduces:

Spain hydraulic cylinder,flange type cylinder manufacturer,flange type cylinder

Spain flange type cylinder

(Spain flange type cylinder,produced by Hengyu Hydraulic Cylinder Factory)

flange type cylinder are widely used in Spain,because of long service life,smooth movement,high work efficiency.So our company has designed flange type cylinder for customers from Spain.

Introduction to flange type cylinder:

The internal leakage of the flange type cylinder is an important indicator to measure the quality of the flange type cylinder: the internal leakage of the flange type cylinder will reduce the volumetric efficiency, increase the temperature rise of the oil, affect the positioning accuracy of the flange type cylinder, so that the flange type cylinder can not accurately and stably stop in a certain position of the flange type cylinder, so it is one of the main indicators of the flange type cylinder.

When the flange type cylinder is customized, if there are high requirements for the quality of the flange type cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the flange type cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the flange type cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

If air enters the hydraulic system, the flange type cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

When purchasing the flange type cylinder, try to clarify the following parameters of the flange type cylinder: A. flange type cylinder diameter, rod diameter, stroke; B. Working pressure or flange type cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right flange type cylinder type can be found accurately and quickly.

Answers to some questions about flange type cylinder:

What is a variable amplitude cylinder?
The type of variable amplitude cylinder is: double acting piston type cylinder, single acting plunger type cylinder, double acting two-stage telescopic cylinder. Double acting piston cylinder is the most common application. The oil cylinder has two oil outlets, and when the oil is fed into the A port, the oil is returned to the B port; If the oil inlet of the B port is returned to the oil of the A port, the reciprocating movement of the piston depends on the effect of pressure. Single-acting plunger (or piston) cylinder has only one oil port, the pressure oil can only supply oil to one side of the plunger in the cylinder, the plunger moves in one direction under the action of pressure oil, and the return stroke of the plunger is driven by the gravity of the lifting arm, such as the LT1040 truck crane variable amplitude cylinder. The double-acting two-stage telescopic cylinder is a set structure, and the two-stage piston rod is like a tie rod antenna set in the cylinder barrel.

Cylinder pressure calculation formula
The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate it according to the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the working pressure P (unit MPa) the thrust of the cylinder F push =3.14*R*R*P (unit N) The pulling force of the cylinder F pull =3.14* (R*R-r* R) *P (unit N).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩MV欧美| av夜夜| www.五月婷婷综合深爱| 老阿婆一区二区三区| www.qinhqingcao| 中文字幕日韩三| 小穴制服丝袜论坛| www.掰开逼| 伦理片网站一群二区| 九九自拍夫妻不卡视频| 老太太区二区精品无码| 男女一起艹鸡巴国产| www..com精品福利| 成人自拍偷拍综合| 午夜紧急福利| 91男女猛烈无遮挡| 男人日日干| 曰小逼视频| 痴汉熟女在线播放| 日本中文字幕成人一区二区三区| 一区视频想要肉棒啊啊| 啊啊嗯啊被操视频| 欧美精品一区 熟女| 欧美缴情一区二区| 欧美3区5区| 被黑人鸡巴挤入视屏| 性感美女被日嗷嗷叫| 日韩无码一区二区啪啪啪| 国产美女无遮挡物免费网站| 神马午夜一区三区五| 深夜抽查高潮视屏| 五月四婷婷在线| 九色91夫妻原创刺激| 在线观看日本一不二不三不四不| 蜜臀后入网址| 老司机在线观看精品视频| 亚洲美女操逼三级| 日韩美女大屁股大鸡巴| 中文字幕在线观| 在线免费观看大鸡巴操小骚穴| 日韩中文字幕无码一区|