亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailboard balance cylinder Sold to El Salvador

Release time:2023-11-12 15:30:07 Hits: Current position: Home > News

This article mainly introduces:

El Salvador hydraulic cylinder,tailboard balance cylinder manufacturer,tailboard balance cylinder

El Salvador tailboard balance cylinder

(El Salvador tailboard balance cylinder,produced by Hengyu Group)

tailboard balance cylinder are widely used in El Salvador,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed tailboard balance cylinder for customers from El Salvador.

Introduction to tailboard balance cylinder:

The viscosity of the working oil used in the tailboard balance cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

The piston seal of the tailboard balance cylinder is the main element to prevent leakage in the tailboard balance cylinder. For the lip seal, it should focus on checking whether the lip edge is bruised and worn, and for the combination seal, it should focus on checking the wear of the sealing surface, and then determine whether the seal can be used. In addition, it is necessary to check whether the static seal between the piston and the piston rod is crushed. The piston rod seal should focus on checking the wear of the seals and supporting rings.

tailboard balance cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the tailboard balance cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the tailboard balance cylinder. c. The tailboard balance cylinder seal is extruded, if the O-ring is obviously extruded at the tailboard balance cylinder seal, replace the tailboard balance cylinder seal.

If the tailboard balance cylinder slips or crawls, please check whether there is astringency inside the tailboard balance cylinder, because the internal parts of the tailboard balance cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the tailboard balance cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the tailboard balance cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

Answers to some questions about tailboard balance cylinder:

Why does the hydraulic cylinder ring?
1 Air intrusion into the hydraulic system is the main reason for noise 2 The relief valve is unstable, such as due to the improper combination of the slide valve and the valve hole or the contact of the cone valve and the seat is stuck by dirt, the damping hole is blocked, the spring is crooked or fails to make the spool stuck or move in the valve hole, causing system pressure fluctuation and noise. 3 Improper adjustment of the reversing valve causes the spool of the reversing valve to move too fast, resulting in reversing impact, resulting in noise and vibration. 4 Mechanical vibration, such as long tubing, elbow more and not fixed, when the oil flow through, especially when the flow rate is high, easy to cause pipe shaking; The rotating part of the motor and hydraulic pump is unbalanced, or the alignment is not good during installation, or the coupling is loose, etc., which can produce vibration and noise.

What is hydraulic cylinder internal leakage and external leakage?
The internal leakage of the hydraulic cylinder refers to the leakage of the piston head seal of the double-acting cylinder, and the leakage occurs inside the cylinder; The external leakage refers to the leakage phenomenon between the cylinder head (or cylinder guide sleeve) and the plunger rod (or piston rod) and the seal between the guide sleeve and the cylinder block, and the oil in the hydraulic cylinder leaks to the outside.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
少妇自慰喷射| 国产激情极品白虎视频| 激情爱爱老外鸡巴蛋蛋久久网站| 男女靠逼视频一区二区| 啊啊高潮| 操无码色| 国产 熟女视频二区| 鸡巴好粗潮喷福利| 五月中文视频| 艹老师骚叫丝袜足交一区日本| 一区日韩高清| 久久久人体福利视频| 久婷婷五月| 波多一区在线| 久热热国产无码| 99操逼视频| 日韩视频干| 一不卡二视频| 鸡巴一区二区三区四区| 精品aV一区二区三区不卡| 蜜桃熟女区| 中文字幕一区二区三区.乱伦| 美国巨屌视频。| 抽插 小穴 流水 视频 | 殴美日韩伦理视频一区在线观看| 忘忧草麻豆工作室| 大吊大香蕉| 国产美女插逼爽喷| av作品免费观看| 嗯嗯呢哪啊好爽视频| 老司机成人激情视频| 好爽好骚网站| 操美国大胸美女| 大鸡吧操逼视频动画版| 一本伊人69| 日韩一级在线播放免费观看| 美女haijiba| 美女操操操| 日美女逼真。爽| 同仁县| 日本二区视频在线观看|