亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo cylinder Sold to Peru

Release time:2023-11-12 15:30:11 Hits: Current position: Home > News

This article mainly introduces:

Peru hydraulic cylinder,servo cylinder manufacturer,servo cylinder

Peru servo cylinder

(Peru servo cylinder,produced by Hengyu Group)

servo cylinder are widely used in Peru,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed servo cylinder for customers from Peru.

Introduction to servo cylinder:

The servo cylinder requires that the filtration accuracy of the system is not less than the 80um, and the oil pollution should be strictly controlled, the oil should be kept clean, the performance of the oil should be checked regularly, and the necessary fine filtration and replacement of new working oil should be carried out.

servo cylinder abnormal sound, hysteresis phenomenon cause and elimination method: the piston rod is extended with abnormal sound and hysteresis, if the servo cylinder is placed for a period of time, the servo cylinder may enter the air, and the movement can be normal after dozens of repeated movements. If it still cannot be eliminated, check whether the load is aligned with the axis of the piston rod; Retracted piston rod installation helps to align the load with the piston rod. If the flow is unstable, it will also lead to abnormal movement of the piston rod. Check the relevant components of the hydraulic system.

When the servo cylinder is customized, if there are high requirements for the quality of the servo cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the servo cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the servo cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

When the initial action of the servo cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the servo cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

Answers to some questions about servo cylinder:

What are the requirements for hydraulic cylinder assembly? ① The installation of the cylinder should be solid and reliable. In order to prevent the influence of thermal expansion, in the case of large stroke and hot working conditions, one end of the cylinder must be kept floating.② pipe connection shall not be relaxed.③ The mounting surface of the hydraulic cylinder and the sliding surface of the piston rod should maintain sufficient parallelism and perpendicality.④ The central axis of the moving cylinder should be concentric with the center line of the load force, otherwise it will cause lateral force, which is easy to wear the seal And piston damage. The greater the distance between the supporting points of the piston rod, the smaller its wear. For the hydraulic cylinder of the moving object, the installation should keep the cylinder parallel with the moving object, and the degree of non-parallelism is generally not greater than 0.05mm/m. ⑤The sealing ring should not be installed too tightly, especially the U-shaped sealing ring.

What is the clearance between the cylinder and the piston?
The gap between the cylinder and the piston in the radius is generally 40 wires, that is, about 0.4mm, and the gap of the cylinder with different diameters will be slightly different. Generally, the inner diameter of the cylinder is larger than the outer diameter of the piston, so as to prevent the friction between the outer surface and the inner surface of the cylinder during the operation of the piston. In order to ensure that the cylinder has a rod cavity and a rodless cavity seal, a sealing device, that is, a sealing ring, is installed on the outer surface of the piston. The sealing ring form is not exactly the same, the O-type sealing ring is generally used under low pressure, and the lip sealing ring is used under high pressure. At the same time, the outer circle of the piston is also equipped with a dust ring and a wear ring. As long as the cylinder seal fails, all the internal seals should be replaced.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
中出 在线中文| 不哈不要不慢点高清在线观看 | 涩3涩3精3品7hqq091b5k| 韩日狠狠干| 让你看骚逼逼AV| 九七成人超碰| 激情成人色图| 在线视频日韩麻豆传媒| 超碰在线日本专区| 日韩综合激情站| 操小逼逼,大鸡巴视频| 国产日本熟女肛交| 鸡巴叉入小逼| 狠插东京热中文字幕| 沈阳人妻操逼视频| 国产少妇操| 中文字幕精品一二三四| 日本黄色骚逼视频| 真人操白虎逼| 中文字幕最新乱伦一区二区三区| 都市激情日韩欧美一区二区三区| 日本一区视频免费看| 人妻熟女网址| 在线观看免费不卡一区二区三区四区| 日韩欧美调教视频网站| 欧美精品国产淫荡一区| 精品老女人淫乱一区二区| 大鸡巴日女人一级视频| 99精品又硬又粗又黄少妇视频| 一区aV中文| 大鸡吧九九| 欧美裸体视频| 超大尺度韩日做爱视频在线观看网站| 嗯嗯啊啊啊啊啊啊啊啊免费视频| 成人动漫午夜Av| 台湾少妇日屄视频| 超碰青青一操| 深夜18+在线视频| 99久久婷婷国内精品2021婷婷| 极品啪啪啪视频入口| 嗯嗯啊视频视频|