亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push and pull the cylinder Sold to Azerbaijan

Release time:2023-11-12 15:31:20 Hits: Current position: Home > News

This article mainly introduces:

Azerbaijan hydraulic cylinder,push and pull the cylinder manufacturer,push and pull the cylinder

Azerbaijan push and pull the cylinder

(Azerbaijan push and pull the cylinder,produced by Hengyu Hydraulic Cylinder Factory)

push and pull the cylinder are widely used in Azerbaijan,because of no need for deceleration device,long service life,smooth movement.So our company has designed push and pull the cylinder for customers from Azerbaijan.

Introduction to push and pull the cylinder:

The meaning of the push and pull the cylinder model marked by the push and pull the cylinder manufacturer: for example, 160/100-1150, its meaning: from a professional point of view, 160 refers to the push and pull the cylinder diameter, which is 160mm, and the 100 behind refers to the rod diameter, which is 100mm. The 1150 refers to the push and pull the cylinder stroke, which is 1150mm. Therefore, on this point, we should have a correct understanding and can not make mistakes.

When the push and pull the cylinder is repaired, its inner and outer diameter and roundness should be accurately measured. If the inner hole of the push and pull the cylinder is badly worn, it can be repaired by grinding the mandrel or honing on the boring machine. If the piston is worn, it can be repaired by electroplating, and serious wear should be replaced.

When the push and pull the cylinder is customized, if there are high requirements for the quality of the push and pull the cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the push and pull the cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the push and pull the cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

push and pull the cylinder body inspection: The inner surface of the push and pull the cylinder and the piston seal are the main factors causing the leakage in the push and pull the cylinder, if the push and pull the cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the push and pull the cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

Answers to some questions about push and pull the cylinder:

What does the maximum output force of the cylinder piston mean?
The maximum output of the cylinder is related to the pressure of the hydraulic system that you link to the cylinder. For example, the rated maximum output thrust of the MOB 50 cylinder is 1.3 tons and the rated pressure is 7Mpa. That is, when the input hydraulic oil pressure of the cylinder reaches 7Mpa, the maximum output thrust of the cylinder is only 0.98 tons. When the input hydraulic pressure is only 5Mpa, the maximum output thrust of the cylinder is 1.3 tons. Because the pressure of the cylinder limit is only 7Mpa, if the oil pressure of the input system exceeds 7Mpa, the cylinder can not withstand the pressure burst, and it is damaged.

What adhesive should be used when the cylinder is cracked?
There is a kind of cast iron glue, industrial products market can buy, A, B formula, that is, a tube is A, a tube is B, when used proportionally prepared, check the instructions. Polish the glue after it dries, and then grind it again.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
痴女M男一区二区在线播放| 午夜专区免费一区| 老熟女一区在线视频| 免费观看日韩黄色电影| AV 在线 超碰| 在线看日本中出视频| 91福利后入在线观看| 干德国老熟女| 啊啊啊好舒服嗯啊啊啊视频| 国产精品麻豆果冻传媒在线观看| 强壮的公侵犯一区二区三区日本 | 大骚逼肏屄精品| 老a一区二区三区亚洲| 可乐福利区在线看| av男人的午夜做爱天堂| 日逼一区| 婷孃丁香七月| 欧美青青嘲视频| 操丝袜女一起操| 啊啊啊啊啊大鸡吧视频| 激情短视频久久| 丝袜美腿一区二区三区免费视频| 97涩涩在线| 骚妇videos| 熟妇人妻精品一区二区| 中文字幕av大鸡巴| 精品一区二区长腿久久| 波多野结衣视频一区二区三区| 91蜜桃传媒一区二区三区| 台湾啪啪福利| 白云视频一区二区涩涩视频| 人妻色图 蜜桃视频| 天天舔夜夜添| 日韩熟女欧美| 欧美亚洲一区二区无码| 交口县| 白虎白浆美女视频| 要看网欧美精品| 禁美女网站在看| AV无套第一页| 蜜桃麻豆WWW久久详情|