亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

forklift lift cylinder Sold to Dominica

Release time:2023-11-12 15:32:59 Hits: Current position: Home > News

This article mainly introduces:

Dominica hydraulic cylinder,forklift lift cylinder manufacturer,forklift lift cylinder

Dominica forklift lift cylinder

(Dominica forklift lift cylinder,produced by Hengyu Hydraulic Cylinder Factory)

forklift lift cylinder are widely used in Dominica,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed forklift lift cylinder for customers from Dominica.

Introduction to forklift lift cylinder:

The body of the forklift lift cylinder on the processing process requirements: the body of the forklift lift cylinder is an important and essential part of the forklift lift cylinder, because it has an irreplaceable role. The processing requirements for this part are very high, requiring that the surface roughness of the forklift lift cylinder after processing should reach 0.4-0.8um, and the coaxiality and wear resistance requirements are also very high.

If the seal of the forklift lift cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and forklift lift cylinder, and the phenomenon of "pulling the forklift lift cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

forklift lift cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the forklift lift cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

forklift lift cylinder abnormal sound, hysteresis phenomenon cause and elimination method: the piston rod is extended with abnormal sound and hysteresis, if the forklift lift cylinder is placed for a period of time, the forklift lift cylinder may enter the air, and the movement can be normal after dozens of repeated movements. If it still cannot be eliminated, check whether the load is aligned with the axis of the piston rod; Retracted piston rod installation helps to align the load with the piston rod. If the flow is unstable, it will also lead to abnormal movement of the piston rod. Check the relevant components of the hydraulic system.

Answers to some questions about forklift lift cylinder:

Slide weight 35 kg exit stroke 55mm, is it suitable to use 40 cylinder diameter cylinder?
The maximum output force of the 40-bore hydraulic cylinder can reach 2 tons, and whether it can be used depends on the use scenario. In addition, the problem of mechanism stuck has nothing to do with the size of the power source, and reasonable structural design and good machining and assembly accuracy are the key.

What is the principle of electric cylinder?
Principle: The electric cylinder converts the rotating motion of the motor into the linear motion of the push rod through the mechanical movement of the lead screw and the lead screw pair. With the closed-loop control characteristic of servo motor, the precise control of thrust, speed and position can be realized easily. Using modern motion control technology, numerical control technology and bus (network) technology, the program and bus (network) control is realized. Because of its easy control and use, it will realize the precision motion control that the cylinder and hydraulic cylinder drive can not achieve. Electric cylinder application field: 1, coordinate manipulator: logistics transmission, automated production line. 2. Wave making machine. 3, parallel mechanism: experimental platform, simulation platform, antenna. 4. Parallel machine tools. 5. Medical equipment: CT, Kamar

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
嗯~嗯嗯嗯嗯嗯啊啊啊啊啊在线观看| 未亡人电影在线观看中文字幕| 人妻熟女 - 蜜桃视频| 国产亚洲精品九九九九999九九| 簧片日韩超碰99热| 我要操美女大逼| 欧美一区高清视频在线观看| 熟女小穴一区二区三区| 日本女人日B照片| 日本一区二区三区四区在线观看| 91大神调教视频| 看国产美女直播逼| 哟哟色AV| 婷婷五月在线精品| 高清日韩无码毛片| 外国美女裹鸡巴国产网站| 亚洲精品国偷色| 操逼鸡巴两个鸡巴操| 性夜夜久夜夜| 美国无码AV| 操黑白丝袜美女的逼网站 | 性感AV一二三四区| 色婷婷av激情一区二区三区| 海外福利在线视频| 小骚逼等你来操| 一二三四区在线播放| 骚逼AV网| 美女露乳头www一区二区三区| 亚洲高清av一区二区| 国产二区三区精品福利在线播放| 美女视频自扣看看网站| 俄罗斯老太太操逼网站| 红桃网站AV| 中文字幕大屁股一区| 性生话一级视频欧美黑人| 美女被操穴| 怡红院亚洲第一综合久久| 9av艹艹艹你鸡吧| 花垣县| 日韩干干干| 啊…日我视频|