亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tilting furnace hydraulic cylinder Sold to Congo

Release time:2023-11-13 11:19:05 Hits: Current position: Home > News

This article mainly introduces:

Congo hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

Congo tilting furnace hydraulic cylinder

(Congo tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

tilting furnace hydraulic cylinder are widely used in Congo,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed tilting furnace hydraulic cylinder for customers from Congo.

Introduction to tilting furnace hydraulic cylinder:

Do not enter foreign bodies when installing the tilting furnace hydraulic cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

The material of the sliding part of the tilting furnace hydraulic cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

Most of the failure of the tilting furnace hydraulic cylinder is because there is a foreign body in the tilting furnace hydraulic cylinder into the failure of the tilting furnace hydraulic cylinder, the most problematic is that it is difficult to determine when the foreign body is into the tilting furnace hydraulic cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

The tilting furnace hydraulic cylinder can not be used as grounding electrode to avoid electric damage to the piston rod.

Answers to some questions about tilting furnace hydraulic cylinder:

What are the connection methods of the hydraulic cylinder? The connection modes of the cylinder and the actuator are earring connection, hinge shaft connection, thread connection, etc. The connection modes of tubing and cylinder are threaded connection, flange connection, etc.

What parameters do I need to provide when purchasing hydraulic cylinders?
The main technical parameters of the hydraulic cylinder: 1. Cylinder diameter; Cylinder diameter, inner diameter size; 2. Piston rod diameter; 3. Cylinder stroke; 4. Cylinder pressure; The working pressure of the cylinder is often calculated using the test pressure, which is less than 16MPa multiplied by 1.5 and higher than 16 multiplied by 1.255. Import and export diameter and thread parameters; 6. Whether there is buffer; According to the working conditions, the piston rod extension contraction is generally buffered if the impact is large. 7. Installation method of oil cylinder, etc.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲欧美日韩一区二区三区丝袜熟女| 92国产精品午夜福利免费| 日韩美女午夜福利| 污污的黄片网站免费看| 美女大胸操逼骚逼| 策勒县| 色哟哟哟 免费视频网站| 18禁美女黄网站色大片免费看一| 视频性交色婷婷| 欧美最大胆视频| 黑人大鸡巴狂抽人妻| 欧美性爱推油| 男生操女生下面的网站| 欧美日皮高潮喷水视频| 破处精品一区二区三区| 日本熟妇被操免费网站| 九九操比网站| 日韩不卡一区二区三区四区五区| 性感熟妇五十路| 三级片人妻中出| www.国产大骚逼| 嗯,嗯啊啊好大视频| 国产亂倫強姦高清晰片| 成人手机看片日韩久久| 偷拍自拍日韩精品在线视频| 欧美日韩国产一二三四| 国产经典一级AV| 美女啪啪精品一区| 日本不卡中文一区二区| 淫女露脸久操| 福利一区区| 曰韩久久久久久久内谢| 亚洲色图人妻偷拍| 免费操大逼| 中文人妻熟妇乱又伦精品| 一本道AV九九中文| 二级av网站| 在线女生和男生操| 成年男女福利视频| 女生小视频网址| 怪物操逼性爱动漫网站|