亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steel mill cylinder Sold to Peru

Release time:2023-11-14 08:41:55 Hits: Current position: Home > News

This article mainly introduces:

Peru hydraulic cylinder,steel mill cylinder manufacturer,steel mill cylinder

Peru steel mill cylinder

(Peru steel mill cylinder,produced by Hengyu Hydraulic Co., Ltd)

steel mill cylinder are widely used in Peru,because of long service life,smooth movement,high work efficiency.So our company has designed steel mill cylinder for customers from Peru.

Introduction to steel mill cylinder:

Analysis of commonly used seals: The wear ring and slip ring commonly used on the steel mill cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

In the process of using the steel mill cylinder, sometimes such a problem will occur, the steel mill cylinder can not act immediately after the instruction of the steel mill cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil steel mill cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

When the steel mill cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

The commonly used buffer structure of the steel mill cylinder is composed of a piston boss and a steel mill cylinder head groove. When the piston moves close to the steel mill cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

Answers to some questions about steel mill cylinder:

How to use a solenoid valve to control the expansion of a cylinder? Doesn't the solenoid valve only control on/off?
Use the solenoid valve P into A-B (generally equipped with oil circuit board) to connect the oil inlet interface at both ends of the cylinder, and the solenoid valve can be realized by power off (refer to the solenoid valve 2B2L, different solenoid valve actions are different).

How to distinguish the size of hydraulic cylinder cavity?
The hydraulic cylinder has a rod cavity and a rodless cavity. The rod cavity is the cavity that the piston rod extends out. The rod cavity is of course small due to the existence of the piston rod. That's just relative.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
深爱成人五月激情不卡| 操欧美成人| 久久得得网| 国产女人乱| 女生张开腿让我桶| 插日操| 1区2区3区在线观看日韩| 爱爱激情综合网| 国产区红桃视频| 熟妇色操日本SSS| 又色又爽又黄国产小视频| 果冻传媒操逼视频| 强奸白丝美女在线播放| 美裸操爽歪歪| 国产91精品社区| 五月激情综合亚洲| 插b美女插插b| 粉嫩小泬极品虎白女AV| 亚洲去网干| 无码性爰日韩| 大保健国产国语对白视频| 沈阳市| 嗯嗯嗯啊啊啊免费视频观看网址| 我日少妇逼视频啊啊啊啊| 婷婷五月天影音先锋| 老湿视频69福版| 日韩人体艺术电影一区二区三| 插入啊啊啊在线观看| 女女同女女同性一区二区三区在线| 国产欧美精品一区二区三区麻豆、| 超黄小黄片插入免费| 操B大jb| 加勒比国产高清无码| 高潮熟女一区二区三区| 91电影大神| 91麻豆精品首页| 中日韩欧美人妻| 手里俱乐部五十路六十路AV| 开裆激情欧美激情一区二区中文字幕| 影视成人18禁大鸡巴视频网站| 国产大鸡巴骚b|