亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stroke adjustable cylinder Sold to Czech Republic

Release time:2023-11-15 10:42:01 Hits: Current position: Home > News

This article mainly introduces:

Czech Republic hydraulic cylinder,stroke adjustable cylinder manufacturer,stroke adjustable cylinder

Czech Republic stroke adjustable cylinder

(Czech Republic stroke adjustable cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stroke adjustable cylinder are widely used in Czech Republic,because of powerful torque,long service life,smooth movement.So our company has designed stroke adjustable cylinder for customers from Czech Republic.

Introduction to stroke adjustable cylinder:

The advantages and disadvantages of the stroke adjustable cylinder: the surface of the stroke adjustable cylinder by painting, coating protection treatment, bright luster is not easy to rust, all raw materials of the stroke adjustable cylinder through the top heat treatment, high manufacturing precision, belongs to the precision machinery, has a simple structure, stable quality, high mechanical efficiency, easy to achieve automation and many other advantages. However, hydraulic technology also has the shortcomings of oil leakage, oil temperature change affecting the control of running speed, noise, expensive cost and high maintenance cost.

The difference between the plunger stroke adjustable cylinder and the piston stroke adjustable cylinder is that the piston in the stroke adjustable cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type stroke adjustable cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

The stroke adjustable cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the stroke adjustable cylinder should pay attention to: the operation should be as far away from the stroke adjustable cylinder as possible, to avoid falling objects, knocking, rubbing the stroke adjustable cylinder coating. When cleaning the stroke adjustable cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the stroke adjustable cylinder when the oil temperature exceeds 70 ° C.

Protection of the stroke adjustable cylinder surface: During the dismantling process, safety protection should be carried out on the stroke adjustable cylinder to prevent objects from falling and welding slag from falling to the surface, causing damage to the stroke adjustable cylinder surface. In the process of propulsion, the damaged pipe segments should be prevented from falling and smashing, and the slurry remaining on the surface of the stroke adjustable cylinder should be cleaned up in time.

Answers to some questions about stroke adjustable cylinder:

About the hydraulic cylinder wall thickness problem?
Hydraulic cylinder wall thickness calculation formula: t=PD/200St= pipe wall thickness (minimum thickness) mmP= maximum pressure kg/cm2? d= inner diameter mm? S=δ/5 safety factor δ= minimum tensile strength This case: set the cylinder material 45#, tensile strength 58kg/cm2t=(640X40)/(200X11.6)t=11mm piston output (i.e. Thrust) calculation formula: F1=PD2X(3.14/4)F1=640X42X0.785=8,038kg Note: Square numbers will not be used, all 2's in the text are square codes.

What is the pressure provided for a 63-bore cylinder with a pressure of 2 mpa?
2 mpa pressure is equivalent to 20 kg per square centimeter, 6.3 cm straight longitude, 3.15 cm radius, square, multiplied by, calculated an area of about 31.5 square centimeters, multiplied by 20 kg, the pressure is about 630 kg.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
黑鸡巴操免费在线视频| 人妻AV色欲久久一区二区三区| 先锋伦理啪啪| 蜜乳一区二区在线播放| 国产经典亚洲国产AV| 免费视频在线观看美女网站1000| 91精品国产人妻| 怡红院全部视频| 午夜福利专区一场| 欧美日皮高潮喷水视频| 亚洲日韩精品欧美成人红桃| AV户外骚逼| 韩国版操逼| 大香蕉66区| 透逼免费视频| 亚州欧美另类| 呀呀呀啊啊啊操操操| 噜噜噜国产精品| 五月激情六月亚洲| 武安市| 国产 日韩 成人| 超碰新碰| 一区二区日美女逼视频| 一区二区 日韩女优| 色婷婷av一区二| 亚洲香蕉手机视频| 亚洲AV天天射| 及屌中出在线| 超碰在线三级片| 国产人妻欧美制服| 日本视频88| 欧美熟女内射网址| 竹梅兰菊成人一区二区三区| 欧美日韩成人一级生活片在线观看| 五月婷婷之激情综合| 啊啊啊日韩精品| 国产AV探花系列| 少妇被粗大的猛烈进出的免费视频| 韩国美女日B视频| 69视频蜜臀| 胖女人操逼朝韩|