亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to France

Release time:2023-11-08 08:11:50 Hits: Current position: Home > News

This article mainly introduces:

France hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

France trunnion cylinder

(France trunnion cylinder,produced by Hengyu Group)

trunnion cylinder are widely used in France,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed trunnion cylinder for customers from France.

Introduction to trunnion cylinder:

The coordination of the sliding parts of the trunnion cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

The trunnion cylinder is not the same as the trunnion cylinder, because the pressure of the pneumatic system is generally within the range of 0.2-1.0Mpa, the trunnion cylinder can not be used as a high-power power component, but the trunnion cylinder can be used as a relatively large power component, or the trunnion cylinder system can be used.

The repair method of trunnion cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

In recent years, the processing process of the trunnion cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

Answers to some questions about trunnion cylinder:

How to control the speed of the cylinder?
High demand control, it is necessary to use servo closed-loop control, you can adjust the speed at will. Reference: Hydrodynamic Motion Control Practical Design Guide.

How does the clamping cylinder work?
Hydraulic transmission principle: oil as the working medium, through the change of the sealing volume to transfer movement, through the internal pressure of the oil to transfer power. 1. The power part - converts the mechanical energy of the prime mover into the pressure energy of the oil (hydraulic energy). For example: hydraulic pump. 2, The executive part - the hydraulic pump input oil pressure energy into the mechanical energy to drive the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3, The control part - used to control and adjust the oil pressure, flow and flow direction. For example: pressure control valve, flow control valve and direction control valve. 4, The auxiliary part - the first three parts are connected together to form a system, which plays the role of oil storage, filtration, measurement and sealing.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女在线无遮挡www| 开 心 色色激情网| 亚洲一二三区不卡AV在线| 歐美作愛A級片| av男人专区| 熟女久久精品一区二区| 大鸡巴插小逼视频网站| 性久久激情视频| 国产乱伦视频网站| 亚洲一区二区成人不卡视频| 在线观看B片| 综合激情五月综合激情五月激情1 欧美日韩一级黄色免费不卡 | 欧美日韩国产另类诱惑| 四虎大骚逼| 国产大鸡巴肌肉男操美女AV| 抽插视频中文字幕| 日本福利一区| 欧美一区二区三区四区理伦片| 好吊操视频免费在线| 美女乳头一区二区| 操逼视频在线下载| 日本不卡一区二区视频在线播放| 用力吸我下面在线视频在线观看| 大香蕉视频青青| 亚洲婷婷五月激情网| 超碰 麻豆| 91欧美巨屌| 操操亚洲AV| 麻豆国产HDXXXXvideo| 香蕉婷婷久久| 另类日韩欧美综合| 我日少妇逼视频啊啊啊啊| 一区二区三区四区五区中文字幕在线观看| 操操操操骚逼女人| 美女白虎骚逼被插| 亚洲高清av一区二区| 深爱四房播播五月激情网| 人妻精品一区二区三区蜜桃| 日区成人一区二区三区| 最近女生被操视频在线播放一区二区 | 国产96色|