亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailboard balance cylinder Sold to Malaysia

Release time:2023-11-16 08:44:57 Hits: Current position: Home > News

This article mainly introduces:

Malaysia hydraulic cylinder,tailboard balance cylinder manufacturer,tailboard balance cylinder

Malaysia tailboard balance cylinder

(Malaysia tailboard balance cylinder,produced by Hengyu Hydraulic Cylinder Factory)

tailboard balance cylinder are widely used in Malaysia,because of no need for deceleration device,long service life,smooth movement.So our company has designed tailboard balance cylinder for customers from Malaysia.

Introduction to tailboard balance cylinder:

How the cavitation of the tailboard balance cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the tailboard balance cylinder, resulting in corrosive damage to the parts.

When the tailboard balance cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

The viscosity of the working oil used in the tailboard balance cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular tailboard balance cylinder action. Troubleshooting method: Replace the rubber hose.

Answers to some questions about tailboard balance cylinder:

What welding rod is used for hydraulic cylinder welding?
There are several reasons for bad welding of hydraulic cylinder: 1. There is hydraulic oil on the welding surface, wipe it with a rag, there will be bubbles in the welding process, and it will not last for a few days. You have to remove it, drain it, wash it off with gasoline and try again. 2. Open the groove before welding, it is not deep enough to use the Angle grinding machine, and can not find the accurate crack position. 3. The material of the cylinder itself is not clear, the welding performance of more than 35 steel is not good, in the factory welding needs to preheat, the welding rod should also be dried and insulated, there is no such condition on the site.

How to distinguish large cavity and small cavity of excavator rod cylinder ?
Single rod piston cylinder is a form of cylinder that is used relatively most, and the boom, bucket, dozer shovel cylinder are all in this form. Among them, the rodless cavity is also called the large cavity, and the rodless cavity is also called the small cavity. Therefore, the cylinder cavity on the side with the exposed piston rod is the small cavity, and the cylinder cavity on the side without the exposed rod is the large cavity.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
午夜精品美女玖玖| 日韩忆红院| 操逼逼网站| 欧美黑人大鸡巴aaaa| 美女裸体被我捅网站免费| 自慰在线精品| 热久久视久久精品2019| 性感美女大操逼大鸡巴| 五月 婷婷 成人| 久久性生活视屏| 丝袜人妻中文字幕第一页| 欧美黄色精品一区| 日本色播播| 芭焦视频官方网站| 日本熟妇诱惑| 欧美日韩无删减| 人妻少妇精品无| 九九热的Av| 中文字幕日产人妻久久| 性情网站在线观看日韩| 丝袜黄片视频国产免费| 九九九九九九九操| 五月草av在线| 深夜福利小视频免费在线观看视频网站 | 老湿机亚洲| 都市淫乱大香蕉| 女生裸体视频二区| 久久久裸体视频中文字幕| 扬州市| 熟女无码在线一二三四五6区| 高清传媒一区不卡| 午夜无码精品一区二区三区蜜桃臀| 国产乱码日韩亚洲精品成人| 内射射满骚逼| 操逼王操美女| 台湾佬久久婷婷| 城步| 手机看激情福利视频| 亚洲一区二区三区四区婷婷香蕉| av一区二区免费在线| 超碰在线国产福利|