亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

single rack cylinder Sold to Cameroon

Release time:2023-11-18 17:15:13 Hits: Current position: Home > News

This article mainly introduces:

Cameroon hydraulic cylinder,single rack cylinder manufacturer,single rack cylinder

Cameroon single rack cylinder

(Cameroon single rack cylinder,produced by Hengyu Group)

single rack cylinder are widely used in Cameroon,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed single rack cylinder for customers from Cameroon.

Introduction to single rack cylinder:

After the single rack cylinder is installed, lubricating grease should be added to the relative moving parts such as earring and middle hinge shaft before trial operation.

single rack cylinder body inspection: The inner surface of the single rack cylinder and the piston seal are the main factors causing the leakage in the single rack cylinder, if the single rack cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the single rack cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

When the single rack cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

The piston rod of the single rack cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

Answers to some questions about single rack cylinder:

When there is only one hole in the oil inlet and outlet of the hydraulic cylinder, will there be oil leakage?
It is a single acting oil cylinder. This oil cylinder is always driven by hydraulic oil in advance, and is generally pulled back by the spring at the bottom of the piston or the weight of the cylinder piston or the load. But either way, it has nothing to do with any internal leakage. Whether the oil is internally drained is related to the sealing and accuracy of the cylinder itself.

CNC lathe rotary cylinder oil leakage and treatment methods
Oil leakage often occurs when the cylinder (especially the hollow cylinder) of the CNC lathe is installed. First check the cylinder yaw, be sure to reach or close to the required value, generally the cylinder requires the outer beat within 1 wire. Otherwise, too much beating is sure to leak oil. Then check whether the tubing is smoothly downward at a certain Angle, and can not bend. Look at the pipe outlet can not go into the oil level, to a little higher. Otherwise, there's back pressure and it's gonna leak.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
极品美女毒龙视频大全| 亚洲日韩网站一线二线| 国产乱伦精品视频区| 自拍偷拍看爽| 男女操逼日韩91| 亚洲专区视频一二三| 吉水县| 大鸡巴插好爽视频| 中文字幕日色| 不卡不卡成人| 亚洲老肥熟| 插日本女人逼视频| 男人和裸体美女操B视频| 区二区三区不卡| 国产一区二区三区AV在线k8| 国产色区一区二区| 赤裸美女网站一区二区三区| www.射伊蕉婷婷| 鸡巴起飞| 山丹县| 最近亚洲精品国产AV| 国产成人AV一区在线观看| 在线老阿姨做爱视频| 得得综合日韩社区在线| 97天天爽天天摸| 亚洲色桃超碰| 中文字幕 区二区三区| 18禁免费网址合集| 91yqeqsqzx| 色色五月亚洲| 亚洲视频官网在线看一二三| 精品人妻一区二区三区18| 亚洲视频一二三四五| 不卡一区二区无码中文字幕| 欧美少妇性生活在线| 大鸡把一二三区| 在线视频二区三区| 国产 日韩 欧美 中文 另类在线| 无码一区二区在线观看一起草av | 亚洲有码第十页| 偷拍午夜福利|