亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

pressure retaining cylinder Sold to Bolivia

Release time:2023-11-19 14:06:19 Hits: Current position: Home > News

This article mainly introduces:

Bolivia hydraulic cylinder,pressure retaining cylinder manufacturer,pressure retaining cylinder

Bolivia pressure retaining cylinder

(Bolivia pressure retaining cylinder,produced by Hengyu Group)

pressure retaining cylinder are widely used in Bolivia,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed pressure retaining cylinder for customers from Bolivia.

Introduction to pressure retaining cylinder:

Under normal circumstances, the pressure retaining cylinder is composed of the rear end cover, body, piston, piston rod and front end cover and other main parts. In order to prevent the working medium from leaking out of the pressure retaining cylinder or from the high pressure chamber to the low pressure chamber, a sealing device (sealing ring) is arranged between the pressure retaining cylinder and the end cover, the piston and the piston rod, the piston and the pressure retaining cylinder, the piston rod and the front end cover. A dustproof device is also provided on the outside of the front end cover. In order to prevent the piston from impacting the end cap when it moves rapidly to the end of the stroke, the end of the pressure retaining cylinder can also be provided with a buffer device. If necessary, the exhaust device should be set in order to exhaust.

The coordination of the sliding parts of the pressure retaining cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

In recent years, the processing process of the pressure retaining cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

The oil pressure retaining cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

Answers to some questions about pressure retaining cylinder:

Why does the hydraulic cylinder rebound after the rod cavity is extended into place?
The reason is that after the rod cavity is extended into place, the rod cavity and the rodless cavity are connected, so that the cylinder moves towards the rod cavity. After connecting, it is equivalent to the hydraulic oil directly driving the cylinder with an area equal to the piston rod. After the end of this problem, it is estimated that the seal is not very good, and the two cavities are connected after the pressure is increased to a certain extent; Or there is a problem in the valve, so that the two chambers are connected after reaching a certain pressure. Other phenomena: If the load is increased to a certain extent, no matter which side of the solenoid valve is energized, the cylinder will move to the rod cavity.

What components can control cylinder rising and falling speed and the speed is adjustable?
A throttle or special solenoid valve is required. The reversing valve can choose the three-position reversing valve with P-type middle function. When rising, the reversing valve can be changed to the middle position to achieve differential connection and the fastest speed. Add a combination valve one-way throttle valve in the oil return circuit, connection mode: when the cylinder rises, the oil flows back to the tank through the check valve, the throttle valve is reversed off, when the cylinder falls, the reversing valve is changed to the left or right position (see the structure of the valve), the check valve is reversed off, the oil returns to the tank through the throttle valve, and the speed can be adjusted through the throttle valve.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
中国大陆探花毛片| 一本之猛搞日韩老女人骚逼| 成人免费黄色网址精品一区二区 | 婷婷色一区二区三期| 再入熟妇骚逼| hj色在线综合视频| 美女女优一区二区| 清纯美女操逼喷水视频| www.国产一级av| 超碰免费公| 国产少妇视频在线| 极品少妇91大神少妇自慰| 欧美字幕成人亚洲区成人中文| 一本之猛搞日韩老女人骚逼| 欧美操逼不卡视频| 啊啊啊啊啊嗯嗯我要视频一区二区| Av天堂电影一区二区| 欧美国产日韩成人影视大全| 青青草原色中色字幕在线免费| 四会市| 嗯嗯啊啊啊啊不要三级在线观看| 国产精品美女破处大全| 欧美破处日韩一区二区| 高清网又粗又大| 精品老湿机免费在线观看| 欧美区亚洲区 日韩区小说区| 国产伊人视频| 久久婷婷五夜综合| 日日操夜夜操人人操人人干| 合江县| 午夜福利国产亚洲| 猛操美女的b免费| 91大神精品视频在线网站| 日韩人妻体内射精一区二区三区| 男女午夜久久久久| 精品偷窥自拍| 黑人巨屌肏屄视频| 中文字幕好看的一区二区三| 蜜臀传媒亚洲| 香蕉一区二区三区飘花| 骚逼成人影院|