亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

synchronous hydraulic cylinder Sold to Dominica

Release time:2023-11-23 08:22:13 Hits: Current position: Home > News

This article mainly introduces:

Dominica hydraulic cylinder,synchronous hydraulic cylinder manufacturer,synchronous hydraulic cylinder

Dominica synchronous hydraulic cylinder

(Dominica synchronous hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

synchronous hydraulic cylinder are widely used in Dominica,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed synchronous hydraulic cylinder for customers from Dominica.

Introduction to synchronous hydraulic cylinder:

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular synchronous hydraulic cylinder action. Troubleshooting method: Replace the rubber hose.

The scar on the sliding surface of the synchronous hydraulic cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the synchronous hydraulic cylinder wall. Therefore, before installation, these scars must be fully repaired.

If the seal of the synchronous hydraulic cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

Most of the failure of the synchronous hydraulic cylinder is because there is a foreign body in the synchronous hydraulic cylinder into the failure of the synchronous hydraulic cylinder, the most problematic is that it is difficult to determine when the foreign body is into the synchronous hydraulic cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

Answers to some questions about synchronous hydraulic cylinder:

What size of hydraulic cylinder is needed for 200 tons pressure? The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate by the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the pressure level P (unit MPa) when working, then the thrust of the cylinder F push =3.14*R*R*P (unit N) the pull of the cylinder F pull =3.14* (R* R-R *R) *P (unit N) 100 tons of the cylinder, System pressure 16Mpa.

What valve is used to control cylinder expansion?
Mainly use reversing valve, but the details of the control need hydraulic control valve, hydraulic control valve can be divided into direction control valve, pressure control valve, flow control valve. The valve controls the expansion of the cylinder is the direction control valve, that is, the reversing valve. What is the meaning of two-position three-way and three-position four-way of the reversing valve? Usually according to the different working positions that can stay after the spool is moved, it can be divided into: two-position valves, three-position valves and multi-position valves. According to the number of different slide valve channels can be divided into: two-way valve, three-way valve, four-way valve, five-way valve and multi-way valve. The name of the reversing valve is called the multi-position and multi-pass reversing valve according to its working position and the number of channels.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
被操一区美女| www操逼91| 农夫导航cc五十路| AVTT天堂网一区| 啊啊啊舒服啊啊啊久久久久久久| 日韩高跟美女日逼视频| 99久re久热996热99| 欧美日韩大陆大片一级二级三级高清无| 日本一区二区三区免费不卡在线| 日一日干操美女视频| 污黄在线三区观看视频| 午夜无码精品一区二区三区蜜桃臀| 神马在线午限福利限制一区二区三区| 欧美激情爆操骚逼视频| avhd0010老司机在线观看| 日韩成人免費黄片| 啊啊啊嗯嗯免费观看| 欧美日韩鸡巴草逼| 3啊啊啊AV| 日韩熟妇性交| 1024看片基地乱伦| 一本岛在线色AV| 男叉女日韩| 大香蕉一区二区视频| 五月天一区二区三区四区| 欧美日韩手机在线大香蕉| 亚洲高清激情AV| 和平区| 丝袜后入91| 红桃AV在线网| 菏泽市| AV日韩一本道在线| 999精品一区| 91丝袜人妻无码| 国产一区二区三区啊啊啊嗯嗯啊啊啊啊啊| 中年熟 老妇 暗网一区| 日本亚洲操逼视频| 插国产骚逼逼内射| 国产.操美女| 免费观看AA视频| 啊啊啊好舒服在线观看视频|