亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

jacking hydraulic cylinder Sold to Angola

Release time:2023-11-24 08:38:56 Hits: Current position: Home > News

This article mainly introduces:

Angola hydraulic cylinder,jacking hydraulic cylinder manufacturer,jacking hydraulic cylinder

Angola jacking hydraulic cylinder

(Angola jacking hydraulic cylinder,produced by Hengyu Group)

jacking hydraulic cylinder are widely used in Angola,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed jacking hydraulic cylinder for customers from Angola.

Introduction to jacking hydraulic cylinder:

Because of the slightly complex structure of the buffer jacking hydraulic cylinder, sometimes there will be problems, such as when the jacking hydraulic cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

In use, the jacking hydraulic cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the jacking hydraulic cylinder.

The piston rod and guide sleeve function of the jacking hydraulic cylinder is crucial: the relative motion pair between the piston rod and the guide sleeve is the main factor causing external leakage, if the chrome layer on the surface of the piston rod is spalling or producing longitudinal tensile marks due to wear, it will directly lead to the failure of the seal.

jacking hydraulic cylinder installation precautions: Before installing the jacking hydraulic cylinder into the system, the parameters on the jacking hydraulic cylinder label should be compared with the parameters when ordering. The base of the jacking hydraulic cylinder must have sufficient stiffness, otherwise the jacking hydraulic cylinder will bend upward into a bow when pressurized, so that the piston rod will bend.

Answers to some questions about jacking hydraulic cylinder:

How to calculate the tonnage of the hydraulic press? Example: The input cylinder pressure is 5Mpa, the end area of the cylinder piston is 100mm, and how much is the thrust tonnage?
F=P*S=5*10^6*3.14*(1/20)^2=39250N.

What adhesive should be used when the cylinder is cracked?
There is a kind of cast iron glue, industrial products market can buy, A, B formula, that is, a tube is A, a tube is B, when used proportionally prepared, check the instructions. Polish the glue after it dries, and then grind it again.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女被在线内射高潮口爆视频| www少妇熟女| 少妇被粗大的猛进进出出免费观看| 日本熟妇视频网址www| 亚洲日韩欧美大尺度在线观看| 欧美首页免费| 女人让男人捅| 在线影院悠悠亚洲一区| 白虎bbbbb视频| 操肏大骚鸡巴| 欧美日韩一级视频真人| 老熟女视频一区| 御姐 一区 二区| 日本激情在线观看| 99九九久久裸体丰满人妻性交| 国产大鸡巴操逼视频| 最新国产福利网| 国产日韩性爰| 精品偷窥自拍| 人妻丰满熟妇91久久九九| 久久香蕉91| 免费亚州熟女| 小骚逼被大鸡吧操免费视频| 日本有码a| 成年人免费午福利| 国产一区二区三区在线高清免费不卡观看| 宝宝好爽…啊啊视频在线观看| 啊..啊..好舒服网站| 欧美精品逼逼逼逼逼| 小穴水多抽插视频| 一区二区三区大鸡巴来使劲日小BB视频| 嗯嗯好舒服嗯快点在线视频| 欧美日韩另类在线观看新蒲京网址| 美女操逼应用视频| 两性午夜福利视频| 国产日韩欧美熟女| 少妇人妻精品成人| 特黄三级又爽又粗又大视频| 午夜十八禁福利视频| 中文字幕乱码精品一区二区三区| 日操大黑逼视频|