亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reciprocating cylinder Sold to Burma

Release time:2023-11-26 09:49:55 Hits: Current position: Home > News

This article mainly introduces:

Burma hydraulic cylinder,reciprocating cylinder manufacturer,reciprocating cylinder

Burma reciprocating cylinder

(Burma reciprocating cylinder,produced by Hengyu Hydraulic Co., Ltd)

reciprocating cylinder are widely used in Burma,because of no need for deceleration device,long service life,smooth movement.So our company has designed reciprocating cylinder for customers from Burma.

Introduction to reciprocating cylinder:

When the reciprocating cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

If it is found that the reciprocating cylinder lubrication is poor or the reciprocating cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the reciprocating cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the reciprocating cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the reciprocating cylinder center line. In this way, when the piston works in the reciprocating cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the reciprocating cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

reciprocating cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a reciprocating cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' reciprocating cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the reciprocating cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The reciprocating cylinder mainly outputs linear motion and force. The reciprocating cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston reciprocating cylinder, plunger reciprocating cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger reciprocating cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular reciprocating cylinder action. Troubleshooting method: Replace the rubber hose.

Answers to some questions about reciprocating cylinder:

What is the HS code of the hydraulic cylinder?
HS code of hydraulic cylinder; 8412210000 8412210000 Linear hydraulic power unit (hydraulic cylinder) 0.12000 0.35000 0.00000 0.17000 0.00000

Why does the hydraulic cylinder ring?
1 Air intrusion into the hydraulic system is the main reason for noise 2 The relief valve is unstable, such as due to the improper combination of the slide valve and the valve hole or the contact of the cone valve and the seat is stuck by dirt, the damping hole is blocked, the spring is crooked or fails to make the spool stuck or move in the valve hole, causing system pressure fluctuation and noise. 3 Improper adjustment of the reversing valve causes the spool of the reversing valve to move too fast, resulting in reversing impact, resulting in noise and vibration. 4 Mechanical vibration, such as long tubing, elbow more and not fixed, when the oil flow through, especially when the flow rate is high, easy to cause pipe shaking; The rotating part of the motor and hydraulic pump is unbalanced, or the alignment is not good during installation, or the coupling is loose, etc., which can produce vibration and noise.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女扒开尿口让人插久久久| 国韩av高清不卡一区二区三区| 能看见美女逼的视频| 日韩av片| 中文字幕有码视频观看| 丝袜美腿3D啪啪| 美女 后入 在线| 国产黄色大片在线| 日本老妇在线一区| 不卡的一区二区在线中文字幕| 大鸡巴爆操小骚逼一区二区三区| 国产精品五一视频 | 肏屄嗯啊视频| 五月婷婷六月丁香| 91热热| 中文字幕一区二区日韩在线观看 | 欧美成人中文字幕网| 狠狠干一干人妻| 啊啊啊好舒服使劲操我视频| 欧美日韩国产最新在线| 日本一区二区三区嗯嗯啊啊| 国产精品z自拍视频| 美女被日比| 美女少妇二区| 亚洲福利视频一区二区三区| 国产免费嘿咻视频在线观看| 亚洲熟女Av一二三四区| 91在线 xxxxx| 久久精品大家还在搜| 高清一级午夜福利67194| 色综综合天堂| 制度色吧综合激情| 红桃AV一区二区乱码| 欧美经典综合一区二区在线播放| 日本免费三级片嗯嗯啊啊| 日韩老女人黄片| 美女骚穴舒服视频| 久久粗进入视频| 色五月欧美视频| 欧美五十路熟| 中日乱码在线一区二区三区在线观看 |