亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

200 ton hydraulic cylinder Sold to Austria

Release time:2023-11-30 10:59:51 Hits: Current position: Home > News

This article mainly introduces:

Austria hydraulic cylinder,200 ton hydraulic cylinder manufacturer,200 ton hydraulic cylinder

Austria 200 ton hydraulic cylinder

(Austria 200 ton hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

200 ton hydraulic cylinder are widely used in Austria,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed 200 ton hydraulic cylinder for customers from Austria.

Introduction to 200 ton hydraulic cylinder:

200 ton hydraulic cylinder spool stuck or valve hole blocked How to solve: When the flow valve or direction valve spool stuck or valve hole blocked, the 200 ton hydraulic cylinder prone to misoperation or action failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium.

When the 200 ton hydraulic cylinder needs to be disassembled for maintenance due to leakage and other faults, the piston should be moved to the bottom position of the 200 ton hydraulic cylinder, and hard beating and sudden drop are strictly prohibited during disassembly.

200 ton hydraulic cylinder body inspection: The inner surface of the 200 ton hydraulic cylinder and the piston seal are the main factors causing the leakage in the 200 ton hydraulic cylinder, if the 200 ton hydraulic cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the 200 ton hydraulic cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

200 ton hydraulic cylinder is the most important part of construction machinery, the traditional processing method is: broaching 200 ton hydraulic cylinder block - fine boring 200 ton hydraulic cylinder block - grinding 200 ton hydraulic cylinder block. The rolling method is: broaching 200 ton hydraulic cylinder block - fine boring 200 ton hydraulic cylinder block - rolling 200 ton hydraulic cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the 200 ton hydraulic cylinder block is about 1-2 days, rolling 1 meter of the 200 ton hydraulic cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the 200 ton hydraulic cylinder increases by 25%. If the 200 ton hydraulic cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality 200 ton hydraulic cylinders, you must take the rolling production process. After the 200 ton hydraulic cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

Answers to some questions about 200 ton hydraulic cylinder:

The inner diameter of the injection cylinder is 203.2mm and the diameter of the screw is 63.5mm. What is the enhancement ratio?
Oil pressure multiplied by the cross-sectional area of the cylinder is equal to the theoretical output force value, and then multiplied by the efficiency of the cylinder is equal to the actual output force value, and the oil pressure can be calculated by inverting the value input.

Does the excavator use a hydraulic cylinder?
First, construction machinery is generally a hydraulic cylinder. Second, hydraulic transmission equipment is usually composed of four components, power, execution, control and auxiliary. And the hydraulic cylinder as a linear reciprocating motion or less than 360. Reciprocating motion of the hydraulic mechanism, simple structure, reliable work, is also widely used in the hydraulic system of the main actuator, it is the prime mover in the form of mechanical energy to drive the hydraulic pump produced by the liquid pressure energy, and then can be directly driven load for reciprocating movement or less than 360.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
老司机精品在线播放| 五月四婷婷在线| 国产久久一区二区三区| 老司机激情福利| 粉色插b视频| 日骚逼视频| 国产夫妻原创AV大片一区二区| 欧美和老女人操屄乱视频| 天天拍天天色天天爽| 看大鸡巴操逼视频黄色| 木下凛凛子在线观看一区二区三区四区| 91黑丝女仆被操| AAA 肏逼片| 日欧美女人户外出精| 男人女大高潮网站| 女同性恋恋一区二区三区 | av在线免费一区二区| 禁网站美女| 兄妹一区二区三区| 91麻豆极品在线播放| 日本无遮挡性爱一区二区三区| 韩国日本伦理一区| http://hzwyli.com/| 操逼视频直接看| 岛国一本在线综合| 大鸡巴 小逼视频| 激情亚洲色图无码中文字幕 | 九色国产视频| 国产天美自拍av| 91果冻堕落人妻玛丽莲内裤| 日韩久久久人妻丰满熟妇| 国产视频 激情文学| 五月狠狠激综合网| 日本无码人妻斩| 从后插视频一区二区| 大黑吊干逼| 操逼的真实视频| 国内熟妇视频| 东京热加勒比无码人妻| 白白白发布一区二区免费视频| 国产第一AV成人|