亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

shearing machine cylinder Sold to Nepal

Release time:2023-11-30 10:59:52 Hits: Current position: Home > News

This article mainly introduces:

Nepal hydraulic cylinder,shearing machine cylinder manufacturer,shearing machine cylinder

Nepal shearing machine cylinder

(Nepal shearing machine cylinder,produced by Hebei Hengyu company)

shearing machine cylinder are widely used in Nepal,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed shearing machine cylinder for customers from Nepal.

Introduction to shearing machine cylinder:

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the shearing machine cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

The definition of the minimum stable speed refers to the minimum movement speed of the shearing machine cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the shearing machine cylinder that undertakes different work has different requirements for the minimum stable speed.

shearing machine cylinder hydraulic oil selection: The recommended working oil viscosity of the shearing machine cylinder is 10 ~ 110cSt (1.8 ~ 15E), ISO VG46 hydraulic oil. The normal working oil temperature is 10 ~ 70℃, and the ambient temperature is in the range of -20 ~ 80℃. When the ambient temperature and service temperature are low, the hydraulic oil with lower viscosity can be selected.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the shearing machine cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

Answers to some questions about shearing machine cylinder:

How to judge the leakage in the cylinder?
Common judgment method: In the production site, people make full use of watching, listening, smelling, touching and other sensory ways, by observing that the cylinder can not move or delay the action or feel the oil temperature change, vibration and noise, etc., and then judge whether the cylinder has internal leakage according to experience. Another method commonly used in the field is to extend the cylinder in place to ensure that the cylinder does not have any load and will not retract (to prevent the cylinder from internal leakage accidents), turn off the machine, and then remove the tubing with the rod cavity, and then press the switch that pulls out the cylinder (do not press the wrong switch). If the oil nozzle with the rod cavity drains the cylinder internally, If there's no oil coming out, you have to think about something else going wrong.

How do hydraulic equipment and hydraulic cylinders maintain a certain pressure after pressing to a certain position?
There are several methods. 1. You can use a constant pressure variable pump to adjust the control pressure of the pump to the pressure required by the cylinder, so that when the cylinder is in place, the pump uses the minimum flow rate to maintain the pressure, and the system is more energy saving. 2. If the pressure is maintained for a short time, a hydraulic control check valve can be added to the oil inlet end of the cylinder to close the cylinder and maintain the pressure. If the volume of the cylinder is large, an accumulator can be added between the valve and the cylinder to maintain pressure for 10-30 minutes. 3. You can add a small flow pump, the large pump after unloading, the small pump has been running, specifically for maintaining pressure.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
午夜福利视频wwwww| 日韩成人精品三级中文| 欧美激情极品日韩| 操女人,五十路| 成人AV女优一区二区三区| 欧美另类BB大| 亚洲人大鸡巴操逼视频| 铜陵市| 超碰一区在线免费观看| 欧美日韩俄罗斯国产视频| 黑人大屌日逼视频| 艹殴美逼逼| 日韩鸡鸡鸡巴日韩| 亚洲探花熟女一区| 在线观看干欧美| 亚洲无限一卡| 超碰视屏日韩公开| 校园射春 亚洲| 嗯啊唔好舒服在线观看| 操b b b| 婷婷五月视频网站| 人妻中出受孕中文字幕在线| 男人 伸进 视频白丝| 欧美色图偷拍一区| 多伦县| 国产黑人大屌前后夹击| 在线看片日本中文字幕| 骚货大鸡巴人妻| 国产日韩黄男插女| 插入美女逼逼视频| 中国夫妻性生活视频网| 亚洲制服丝袜人妻| 操少妇在线视频播放| 大黑鸡巴操女妞网| 深爱五月天激情动片在线播放| A性生活片在线看| 激情文学之日韩成人| 337人体艺术一区二区三区| 亚洲皇宫h网| 北条麻妃一区二区系列| 狠狠狠Av日韩|