亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

pushing cylinder Sold to Slovakia

Release time:2023-11-30 11:00:02 Hits: Current position: Home > News

This article mainly introduces:

Slovakia hydraulic cylinder,pushing cylinder manufacturer,pushing cylinder

Slovakia pushing cylinder

(Slovakia pushing cylinder,produced by Hengyu Group)

pushing cylinder are widely used in Slovakia,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed pushing cylinder for customers from Slovakia.

Introduction to pushing cylinder:

The piston rod of the pushing cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

If the seal of the pushing cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

Before purchasing the pushing cylinder, it is necessary to master the original information and design basis, mainly including: the use and working conditions of the machine; The structural characteristics, load conditions, stroke size and operation requirements of the working mechanism; The selected working pressure and flow of the hydraulic system; The reality of materials, fittings and processes; Relevant national standards and technical specifications, etc.

When the control pressure of the hydraulic system is too low, the pushing cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

Answers to some questions about pushing cylinder:

What does cylinder hob125*100 mean?
HOB is a series of hydraulic cylinder products, the use of pressure 14MPA, tie rod structure. 125 refers to the diameter of the cylinder and 100 refers to the stroke. The unit is millimeters.

How to refuel pneumatic riveting cylinder?
First put the gun flat, that is, horizontally, while pushing the stroke positioning pin and loosen the back cover, rotate to the left for a maximum of five turns, and then use a wrench to loosen the oil sealing screw, slowly add the hydraulic oil and let the air out, fill up to tighten the oil sealing screw. This process of adding hydraulic oil is over.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
啊啊啊好舒服嗯在线观看| 大鸡巴日大逼视频看看免费视频看看| 国产小情侣激情视频| 97人妻鸡巴视频| 美女被鸡巴插进逼| 小个子美女的逼逼好操| 大鸡巴插入美国美女| 久国产精品一区二区| 粉穴美女主播在线求插| 扒开逼操视频| 中国美女性愛| 亚洲无一区AV| 中国夫妻性生活视频网| 岛国浮力视频| 少妇缝18p二区| 91大神调教视频| 美女鸡巴插入视频| 锦州市| 精品视频XNXXCOM| 鳮巴插逼逼| 日韩久久久久久九九九精品| 大香蕉亚州乱伦| 日本三级自拍视频| 使劲草中文字幕| 欧美白浆白虎| 国产精品视频919293| 人妻无码熟妇乱又视频内射| 嗯啊操我好爽视频| 欧美色图 啪啪啪视频| 操BAv美女| 日韩成人网址 婷婷| 蜜臀av少妇| 欧美日韩操逼大全| 制服丝袜诱惑经典在线| 自拍偷拍综合国产| 人妻空姐 制服诱惑| 男生和女生操网战| 一二三四最新中文字幕| 在线黄色大青青香蕉| 国产骚比视频| 亚洲激情小说专区|