亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

Lifting cylinder Sold to Guatemala

Release time:2023-12-05 14:27:12 Hits: Current position: Home > News

This article mainly introduces:

Guatemala hydraulic cylinder,Lifting cylinder manufacturer,Lifting cylinder

Guatemala Lifting cylinder

(Guatemala Lifting cylinder,produced by Hengyu Hydraulic Cylinder Factory)

Lifting cylinder are widely used in Guatemala,because of no need for deceleration device,long service life,smooth movement.So our company has designed Lifting cylinder for customers from Guatemala.

Introduction to Lifting cylinder:

Disassembly Lifting cylinder: When disassembly Lifting cylinder, strictly prevent damage to the screw thread at the top of the piston rod, the screw thread of the Lifting cylinder head and the surface of the piston rod. It should also be noted that the piston cannot be played out from the Lifting cylinder.

Do not enter foreign bodies when installing the Lifting cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

After the Lifting cylinder is installed, lubricating grease should be added to the relative moving parts such as earring and middle hinge shaft before trial operation.

The Lifting cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure Lifting cylinder can use 20 steel pipe, and the high pressure Lifting cylinder can use 45 steel pipe.

Answers to some questions about Lifting cylinder:

Why should the piston rod of the hydraulic cylinder be so precise? If you hope the cylinder has a long service cycle, then all parts need to be high-precision, not only the piston rod, but also the cylinder, the sealing groove, the surface roughness, the cylinder looks very simple. Any hydraulic factory can produce the cylinder, but the good cylinder is difficult to produce.

What is the cause of the sound of the excavator arm cylinder?
Hydraulic excavator cylinder includes boom cylinder, bucket rod cylinder and bucket cylinder, four cylinders. The sound of boom cylinder may be the wear of hydraulic cylinder block bushing, piston rod bushing and shaft pin. The main reason: poor lubrication, followed by improper clearance in the assembly process. Countermeasures: (1) Strictly lubricate each shaft pin at least once every 8 hours when the excavator is initially used for 100 hours and under harsh conditions; In other working conditions, lubricate each pin at least once every 50 hours. (2) If the lubricating oil passage is found to be blocked, it must be stopped for rectification. (3) Require assembly, replacement of all parts of the shaft pin, bushing strictly comply with the assembly testing standards and operating procedures.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩女优嫩草亚洲| 有爽有色的黄片| 你懂的熟女| 日韩丰满人妻乱又伦精品| 大几把插B| 男生 福利 AV 资源 在线看| 日插逼视频免费网站| 国产超碰av在线| 鸡巴插小穴视频无码| 国精产品一区一区mb| 插美女动态| 少妇的色诱| 欧美日韩国产高清在线不卡| 大香蕉欧美一区| 日本高清成人视频一区二区三区| 天天射射射射射射舔舔舔干干干 | 国产亚洲日韩欧美九九九| 嗯嗯…嗯嗯嗯的视频| 色屁屁一区二区三区国产| 91三级大屁股后入剧情| 玖蜜成人在线免费观看| 视频一区二区蜜臀| 日韩一级AV一二三区中文字幕| 虎白女粉嫩小穴一区二区三区免费 | 操B操B色情AⅤ| 人妻专区同性恋| 熟女专场,操50岁老逼 - 31XX| aaaa亚洲一区二区三区在线观| 亚洲成人精品一区二区三区| 中文字幕精品一区二区三区AV| 91美女舔鸡巴| 少妇熟女高清一区二区| 一区二区在线伦理| 白丝袜18禁一区人妻| 大鸡巴操逼视| 在线免费视频中出| 大香蕉后入视频| 五月丁香欧美9| 亚洲无码红桃在线| 亚洲中国偷窥另类| 中国东北老女人性高潮白浆|