亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailboard balance cylinder Sold to Brazil

Release time:2023-11-08 10:36:59 Hits: Current position: Home > News

This article mainly introduces:

Brazil hydraulic cylinder,tailboard balance cylinder manufacturer,tailboard balance cylinder

Brazil tailboard balance cylinder

(Brazil tailboard balance cylinder,produced by Hengyu Hydraulic Cylinder Factory)

tailboard balance cylinder are widely used in Brazil,because of excellent temperature resistance,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed tailboard balance cylinder for customers from Brazil.

Introduction to tailboard balance cylinder:

The pressure of the sliding surface of the tailboard balance cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the tailboard balance cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

Do not enter foreign bodies when installing the tailboard balance cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

The machining accuracy of the tailboard balance cylinder depends on the level of equipment, production technology and testing means. tailboard balance cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular tailboard balance cylinder action. Troubleshooting method: Replace the rubber hose.

Answers to some questions about tailboard balance cylinder:

How is the hydraulic cylinder tempered?
The purpose of the tempering treatment is to make the piston rod have comprehensive mechanical properties of strength, hardness, plasticity and toughness, and the internal structure is uniform and fine tempered sorbite, so as to prepare the organization for subsequent surface quenching. The length of the long cylinder piston rod is 3800-4200, and the diameter is Φ90-Φ110mm, so its heating equipment uses a 150KW well resistance furnace or 600KW suspension continuous resistance heating furnace, and the temperature is controlled by two areas. Heat treatment process parameters: in the shaft furnace, a furnace is suspended with 4 pieces, the quenching heating temperature is 830±10℃, and after holding heat for 160min, it is divided into two times for quenching, and two pieces are quenched each time, and the circulating cooling water is used for cooling.

What is the reason why the hydraulic cylinder is not good at lifting?
There may be several situations 1, whether the slow one is worn 2, whether there is air in the slow cylinder 3, if the two cylinders are supplied by the same oil port, whether the slow joint is blocked (some processing residue will reach a certain oil port under a certain coincidence condition, This situation will not happen if it is not necessarily good before) 4, the oil seal in the slow cylinder leaks, causing the feed oil to leak from the return oil end. Point 4 is most likely because it is invisible and a technical failure. If it is a dual oil feed (separate oil feed), it is also necessary to check the oil supply system and the oil return system (valve type).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女让男人人操一区二区| 午夜精品18 视频国产| bbW逼| 日韩极品中文无码| 欧美暧暧小视频一区二区| 大鸡巴啪啪网| 曰本女人妻操黑人逼| 操大騒逼| 人妻丝袜一区二区三区免费| 欧美大香蕉福利| 在线观看中文字幕一区二区三区| 主播视频一二三区| 操喷高潮视频| 日韩在线久热婷| 嗯嗯啊啊日韩欧美一区二区三区| 日韩视频在线人妻精品五区| 日本中出免费在线| 幸福av导航| 在线观看中文字幕一区二区三区| 黄色电影A| 鸡吧怼逼| 中国人大鸡巴操B视频| 神明视频一区二区| 在线观看韩国成人视频网站| 爱爱午夜福利视频| 美国大屌操欧美女人日| 中文字幕在线1区| 啊啊啊…用力好爽AV| 色五月婷婷激情五月婷婷成人| 在线观看插入曰| 色鸡理论免费观看一区| 密臀成人福利在线| 91涩爱play| 欧美日韩日本视频| 大鸡巴日必内射视频| 久久嗯嗯啊啊视频| 逼操逼操逼操逼| 日韩性爱网络| 久久综合爱爱大全| 鸡巴操死骚逼麻豆| 免费看插动态视频|