亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reset cylinder Sold to S.Africa

Release time:2023-12-09 16:24:28 Hits: Current position: Home > News

This article mainly introduces:

S.Africa hydraulic cylinder,reset cylinder manufacturer,reset cylinder

S.Africa reset cylinder

(S.Africa reset cylinder,produced by Hengyu Hydraulic Cylinder Factory)

reset cylinder are widely used in S.Africa,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed reset cylinder for customers from S.Africa.

Introduction to reset cylinder:

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular reset cylinder action. Troubleshooting method: Replace the rubber hose.

After chrome plating of the piston rod of the reset cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

The definition of the minimum stable speed refers to the minimum movement speed of the reset cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the reset cylinder that undertakes different work has different requirements for the minimum stable speed.

The material of the sliding part of the reset cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

Answers to some questions about reset cylinder:

What is the clearance between the cylinder and the piston?
The gap between the cylinder and the piston in the radius is generally 40 wires, that is, about 0.4mm, and the gap of the cylinder with different diameters will be slightly different. Generally, the inner diameter of the cylinder is larger than the outer diameter of the piston, so as to prevent the friction between the outer surface and the inner surface of the cylinder during the operation of the piston. In order to ensure that the cylinder has a rod cavity and a rodless cavity seal, a sealing device, that is, a sealing ring, is installed on the outer surface of the piston. The sealing ring form is not exactly the same, the O-type sealing ring is generally used under low pressure, and the lip sealing ring is used under high pressure. At the same time, the outer circle of the piston is also equipped with a dust ring and a wear ring. As long as the cylinder seal fails, all the internal seals should be replaced.

Can the hydraulic oil in the cylinder return to the tank?
Yes, there is a way, for example, first remove the cylinder from the machine, and then connect the two pipes on the cylinder, so that the cylinder piston rod is completely retracted into the cylinder, at this time, the piston is with the bottom, and the rear chamber is almost no oil, and then screw off the joint at the end of the front chamber by the hydraulic station, and put it in an empty bucket. Finally, insert the gas pipe into the oil port of the rear chamber. Open the air source, and then the rod will run out, and you'll drain the hydraulic oil from the end of the rod, which requires a source of air on site.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美日韩另类激情| 三级片色五月| 男女操B视频软件| 中文字幕在线播放三区| 老司机av官网在线| 日本天堂中文字幕| 国产亚洲欧洲视频| 一区二区三区五区六区中文字幕| 日韩黄色网络1| 女生被操的视频在线观看| 插我爽视频| 曰本有码在线视频观看视频| 日韩少妇偷夫| 日韩欧美一节片| 中文字幕五六路一区| 日韩一级大胸按摩美女在线看| 日本人妻初脱人妻搭讪| 自拍av一区| 性激情啪啪一二三四五六区| 色情大鸡巴插小穴视频| 欧美精品一区二区三区啪啪| 欧美日韩不卡高清| 硬鸡巴AV| 欧美午夜视频在线| 色久悠悠官方| 色婷| 国产又爽又长| 亚洲国产av综合国产| 操逼网站大鸡巴| 国产精品三级专区av| 囊谦县| 丰满人妻熟女少妇老女人 | 婷婷五月天,欧美熟女| 一区二区毛片级| 亚洲韩国日本在线观看一区二区三区| 九九传媒一区| AV在线播放导航| 97人妻日人妻操人妻浪| 插逼一级视频| 少妇粉穴要棒棒插视屏播放| 插日本女人逼视频|