亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

track steering cylinder Sold to Portugal

Release time:2023-11-12 11:06:10 Hits: Current position: Home > News

This article mainly introduces:

Portugal hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

Portugal track steering cylinder

(Portugal track steering cylinder,produced by Hengyu Hydraulic Co., Ltd)

track steering cylinder are widely used in Portugal,because of long service life,smooth movement,high work efficiency.So our company has designed track steering cylinder for customers from Portugal.

Introduction to track steering cylinder:

When the control pressure of the hydraulic system is too low, the track steering cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

The internal leakage of the track steering cylinder is an important indicator to measure the quality of the track steering cylinder: the internal leakage of the track steering cylinder will reduce the volumetric efficiency, increase the temperature rise of the oil, affect the positioning accuracy of the track steering cylinder, so that the track steering cylinder can not accurately and stably stop in a certain position of the track steering cylinder, so it is one of the main indicators of the track steering cylinder.

If the seal of the track steering cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and track steering cylinder, and the phenomenon of "pulling the track steering cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

If the track steering cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the track steering cylinder. The internal parts of the track steering cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the track steering cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the track steering cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the track steering cylinder bore processing is out of whack. Because the piston and track steering cylinder, guide rail and piston rod are relative If the track steering cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling track steering cylinder weight composition and calculation. The weight of the track steering cylinder is composed of the track steering cylinder diameter, the outer diameter and weight of the track steering cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

Answers to some questions about track steering cylinder:

What is the cylinder with rod cavity, what is the rodless cavity.
The rod cavity is the end of the piston rod, the rodless cavity is the end without the piston rod.

What is the cause of the sound of the excavator arm cylinder?
Hydraulic excavator cylinder includes boom cylinder, bucket rod cylinder and bucket cylinder, four cylinders. The sound of boom cylinder may be the wear of hydraulic cylinder block bushing, piston rod bushing and shaft pin. The main reason: poor lubrication, followed by improper clearance in the assembly process. Countermeasures: (1) Strictly lubricate each shaft pin at least once every 8 hours when the excavator is initially used for 100 hours and under harsh conditions; In other working conditions, lubricate each pin at least once every 50 hours. (2) If the lubricating oil passage is found to be blocked, it must be stopped for rectification. (3) Require assembly, replacement of all parts of the shaft pin, bushing strictly comply with the assembly testing standards and operating procedures.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美日韩免费观看视频| 欧美日韩高清插逼| 最新www国产网站在线观看小视频| 精品乱子伦一区二区三区视频 | 插的高潮了| 免费看紧视频大片| 逼女欧美后入| 欧美大黄白虎| 91亚洲色图| 狂插大逼视频| 男女操B免费视频网| 五十路人妻熟女一区二区三区漫画| 插我逼视频| 欧美熟女在线插| 大鸡巴日进毛逼里小视频| 国产爱玩屁眼的| 美国操逼大鸡巴网站| 色婷婷毛片| 欧洲一区二区在线捅| 大肉榜一进一出视频| 中文字幕在线一区二区高 | 自拍偷拍亚洲中文字幕| AV久久天堂| 欧美人妻三级在线现看中文 | 日本一二区视频在线观看| 白丝大人美女被操| 激情午夜福利视频在线观看| 免费观看老司机在线视频| 操打白虎逼| 骚奶头真硬在线| 久久久久久久舔白| 久草不卡dvd| 一区二区不卡AV| 麻豆传媒18在线观看| 操白虎喷水| 先锋影音 自拍偷拍| 92午夜福利一区二一| 成人自拍亚洲天堂| 祥仔av手机免费看| 欧美日韩黑料专区| 大鸡男女生三级黄色欧美|