亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Jordan

Release time:2023-11-12 15:25:48 Hits: Current position: Home > News

This article mainly introduces:

Jordan hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Jordan swager cylinder

(Jordan swager cylinder,produced by Hengyu Hydraulic Co., Ltd)

swager cylinder are widely used in Jordan,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed swager cylinder for customers from Jordan.

Introduction to swager cylinder:

swager cylinder hydraulic oil selection: The recommended working oil viscosity of the swager cylinder is 10 ~ 110cSt (1.8 ~ 15E), ISO VG46 hydraulic oil. The normal working oil temperature is 10 ~ 70℃, and the ambient temperature is in the range of -20 ~ 80℃. When the ambient temperature and service temperature are low, the hydraulic oil with lower viscosity can be selected.

Classification of swager cylinder: according to the mode of movement it can be divided into linear reciprocating movement type and rotary swing type; According to the effect of liquid pressure, it can be divided into single acting type and double acting type. According to the structure, it can be divided into piston type, plunger type, multistage telescopic sleeve type, pinion and rack type, etc. According to the installation form can be divided into rod, earring, foot, hinge shaft and so on; According to the pressure grade can be divided into 16Mpa, 25Mpa, 31.5Mpa and so on.

When the swager cylinder is customized, if there are high requirements for the quality of the swager cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the swager cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the swager cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

When using the swager cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the swager cylinder block. If the swager cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the swager cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the swager cylinder, so that the working efficiency of the swager cylinder is reduced.

Answers to some questions about swager cylinder:

What is the problem that the cylinder stroke is not in place?
1. Mechanical cause: the piston rod bends; If there is a synchronous cylinder, the stroke of the two cylinders may be different. 2. Hydraulic reason: the system back pressure is too large; The actuator load increases while the system pressure decreases. The electric is not sent, the reversing valve is not reset or stuck, the oil is too dirty, there is gas in the system, the external inertia load is too large, and the cylinder stroke is not in place.

What is the difference between hydraulic piston cylinder and plunger cylinder?
The force surface of the piston cylinder is a rod cavity and a rodless cavity, and the force surface of the plunger cylinder is the plunger, the spring return single-acting piston cylinder can also rely on the external force of the spring to achieve return, the double-acting piston cylinder can produce tension, and the plunger cylinder only produces thrust without tension.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
晶品美女日逼视频免费看| 丁香婷婷五月香蕉91| 亚洲片一区二区| 欧美、日韩、国产视频| 国产精品91探花视频| 一二三区在线精品| 大香蕉视频日韩欧美视频| 江源县| av亚洲国产精品| 激情短视频久久| 大鸡巴爆操小骚逼一区二区三区| 成人片一区二区| 草逼逼欧美| 色欲蜜臀AV 一区二区| 大鸡巴肏屄视频午夜成人| 欧美大屁看逼| 日韩有吗成人在线| 有码无线专区| 日韩理论在线看不卡| 破处福利视频观看| 后入 一区| 国产av二区三区四区五区六区| 国产精品AV99热 | 日韩欧美美女视频| 日韩干综合| 国产1990久久久久久久久久| 亚洲熟女乱综合一区二区| 91后入爆操| 啊啊啊啊太爽了视频一区二区| 色综合大香蕉在线观看 | 极品av在线看免费| 91国产黄片| 办公室护士毛片| 精品一区二区人妻| 精品丰满熟女少妇一区二| 日本精品视频在线| 黄色S色在线观看的免费| 熟女 亚洲一区| 啊啊啊操死我了AV| 日韩国产插逼| 国产精品一区二区三区999.|