亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tension cylinder Sold to Sweden

Release time:2023-11-07 17:47:59 Hits: Current position: Home > News

This article mainly introduces:

Sweden hydraulic cylinder,tension cylinder manufacturer,tension cylinder

Sweden tension cylinder

(Sweden tension cylinder,produced by Hengyu Hydraulic Cylinder Factory)

tension cylinder are widely used in Sweden,because of no need for deceleration device,smooth movement,long service life.So our company has designed tension cylinder for customers from Sweden.

Introduction to tension cylinder:

When the tension cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

When the tension cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the tension cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the tension cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the tension cylinder can meet the requirements by grinding. However, the life and reliability of this repair tension cylinder are not high.

How to repair the tension cylinder body when it is damaged: When the tension cylinder has trace deformation and shallow tensile marks, the tension cylinder is repaired by strong honing process. The heavy honing process can repair tension cylinders up to 2.5 times out of tolerance than the original tolerance. It honed the parts with excessive size or shape error through a powerful honing machine, so that the overall size, shape tolerance and roughness of the tension cylinder can meet the technical requirements.

The repair method of the tension cylinder: the repair of the tension cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

Answers to some questions about tension cylinder:

How to calculate the tonnage of hydraulic cylinder? The tonnage of the cylinder refers to the output force of the cylinder under rated working pressure: 1, for single rod piston hydraulic cylinder, it can be calculated by the area of the circle corresponding to the inner diameter of the cylinder A (square centimeter), and the rated working pressure of the system p (mpa), the value is equal to 10pA kg force, and the ton is 0.01pA. 2, for the double rod piston hydraulic cylinder, with A(square centimeter) to indicate the cylinder cylinder diameter and piston rod outer diameter defined by the ring area, with p (mpa) to indicate the rated working pressure of the system, the output force of the cylinder is 0.01pA ton force.

Why do two hydraulic cylinders lift out of sync?
There may be several situations (do not know the result of the equipment, may not be accurate) 1, whether the slow one is worn 2, whether there is air in the slow cylinder 3, if the two cylinders are supplied by the same oil port, whether the slow joint is blocked (some processing residue will reach a certain oil port under a certain coincidence condition, This situation will not happen if it is not necessarily good before) 4, the oil seal in the slow cylinder leaks, causing the feed oil to leak from the return oil end. Point 4 is most likely because it is invisible and a technical failure. If it is a dual oil feed (separate oil feed), it is also necessary to check the oil supply system and the oil return system (valve type).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
五月婷婷国语| 原创国产色哟哟| 亚州一二三区精品avv| 超碰最新中文字幕不卡| 美女被日B视频| 前列腺高潮网站做爱美国| 精品熟女少妇久久| 性奴人妻啪啪啪| 欧美人妻系列中文字幕第一页| 亚洲丝袜一二三| 鸡鸡透女生视频免费网页| 中文色中出在线| 中文有码二页| 怡红院视频免费| 亚洲3344在线观看| 欧美在线免费小视频 | 美女操鸡吧流骚水视频| 日本黄色sm网站在线观看| 一区二区三区牛牛| 国产伊人视频| 丁香七月欧美综合激情电影婷婷| 婷婷五月亚洲色| 英法日美女操逼免费看| 嗯嗯啊啊好舒服在线视频| 日韩中出人妻一区二区| 欧美性爱插逼视频| 中国美女不卡视频1区2区3区| 中国熟妇老妓女| 大力中出后入人妻中出后入| 老司机精品在线-经典成人直接看| 大鸡巴操骚逼里面观看| 久久精品中国人| 大鸡巴和美女在线欧美| 熟女 人妻 人妻のAV| 最新韩国日本性爱视频| 鸡巴好大免费视频| 日逼88| 中文字幕 欧美 暴力| 中出 亚洲 区一| 欧美日韩一级片免费观看| 日本黄色片网址大全一区二区|