亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

supporting cylinder Sold to Oman

Release time:2023-11-13 11:19:27 Hits: Current position: Home > News

This article mainly introduces:

Oman hydraulic cylinder,supporting cylinder manufacturer,supporting cylinder

Oman supporting cylinder

(Oman supporting cylinder,produced by Hengyu Hydraulic Cylinder Factory)

supporting cylinder are widely used in Oman,because of long service life,smooth movement,high work efficiency.So our company has designed supporting cylinder for customers from Oman.

Introduction to supporting cylinder:

The supporting cylinder requires that the filtration accuracy of the system is not less than the 80um, and the oil pollution should be strictly controlled, the oil should be kept clean, the performance of the oil should be checked regularly, and the necessary fine filtration and replacement of new working oil should be carried out.

How to determine the working pressure of the supporting cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, supporting cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

Before purchasing the supporting cylinder, it is necessary to master the original information and design basis, mainly including: the use and working conditions of the machine; The structural characteristics, load conditions, stroke size and operation requirements of the working mechanism; The selected working pressure and flow of the hydraulic system; The reality of materials, fittings and processes; Relevant national standards and technical specifications, etc.

The supporting cylinder is mainly composed of body, piston, piston rod, supporting cylinder head, supporting cylinder bottom, piston rod head and related auxiliary devices. The piston divides the supporting cylinder into two chambers, and moves reciprocally in the supporting cylinder with the help of pressure oil. In order to improve its working effect, there is no sealing ring on the piston to eliminate internal leakage, where the piston rod passes through the supporting cylinder head, due to the existence of the gap, it is easy to produce external leakage phenomenon, and the dust can enter the supporting cylinder through the gap, so the sealing device and dust prevention reason are set. At the same time, in order to eliminate the influence of eccentric load on the work of the piston, all the supporting cylinders must be provided with a considerable length of guide sleeve at the extended end of the piston rod. In addition, in the case of faster piston movement, the phenomenon of mechanical collision between the piston and the supporting cylinder bottom and the supporting cylinder head is serious, so the buffer deceleration should be set at both ends of the supporting cylinder The working medium of the supporting cylinder: because it works at room temperature, the ordinary oil-type hydraulic oil can be selected; supporting cylinder sealing device: The use of Yx sealing ring, polyurethane (PU) and polytetrafluoroethylene (PTFE) materials combined to achieve a good sealing effect; Buffer mechanism of the supporting cylinder: The buffer structure of the supporting cylinder is to prevent the piston from colliding with the supporting cylinder head at the end of the stroke.

Answers to some questions about supporting cylinder:

What adhesive should be used when the cylinder is cracked?
There is a kind of cast iron glue, industrial products market can buy, A, B formula, that is, a tube is A, a tube is B, when used proportionally prepared, check the instructions. Polish the glue after it dries, and then grind it again.

What is the difference between hydraulic piston cylinder and plunger cylinder?
The force surface of the piston cylinder is a rod cavity and a rodless cavity, and the force surface of the plunger cylinder is the plunger, the spring return single-acting piston cylinder can also rely on the external force of the spring to achieve return, the double-acting piston cylinder can produce tension, and the plunger cylinder only produces thrust without tension.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
免费观看一区二区三区| 国产激情文学网| 香蕉色98| 日本一级A片一区二区| 亚洲人妻欧美精品久久| 激情一区二区在线| 欧美另类BB大| 国产美女操鸡吧| 九一无码视频一区二区三区| 天天操天天操夜夜干| 操吊网| 视频1区2区中文字幕人妻日韩| 老熟女av在线播放导航网站| 色哟哟哟精品一区三区| 欧美美臀一区二区三区......| 黄色录像大香蕉| 微拍福利一区福利二区| 五月激情网 淫淫网| 一本大道AV伊人久久综合| 一区二区 日韩女优| av插入大鸡巴中出| 无码插B| 男人天堂国产免费| 操的我好舒服的视频国产| 看免费插美女视频| 日韩潮喷图片| 欧美美女坝几吧操| 精品美女在线拍| 成人大B网| 大胆日逼美女| 干B视频在线观看| 黑人精品一区二区| 丰满的大胸日韩欧美精品酒店| 无码抽插巨| 人人鲁人人操在线| 国产在线无圣光| 国产人妻人伦精品1国产丝袜| 抽查处女成人免费视频| 日逼国产| 亚洲 探花| 五十路亲子中出在线观看视频|