亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

shearing machine cylinder Sold to Ecuador

Release time:2023-11-13 11:19:28 Hits: Current position: Home > News

This article mainly introduces:

Ecuador hydraulic cylinder,shearing machine cylinder manufacturer,shearing machine cylinder

Ecuador shearing machine cylinder

(Ecuador shearing machine cylinder,produced by Hengyu Group)

shearing machine cylinder are widely used in Ecuador,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed shearing machine cylinder for customers from Ecuador.

Introduction to shearing machine cylinder:

If the seal of the shearing machine cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and shearing machine cylinder, and the phenomenon of "pulling the shearing machine cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

When the shearing machine cylinder is installed, the piston and the shearing machine cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the shearing machine cylinder head boss is easy to cause scars when it hits the inner surface of the shearing machine cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized shearing machine cylinders, only careful and careful operation can be avoided.

Regular maintenance of the shearing machine cylinder includes: regular tightening, shearing machine cylinder fastening screws and gland screws, shearing machine cylinder piston rod stop adjustment screws, should be tightened once a month, tighten each screw evenly, and achieve the corresponding tightening torque. Replace the seal regularly, it is recommended to replace the seal of the shearing machine cylinder once a year. Clean regularly, the shearing machine cylinder is cleaned every other year, and the seals are replaced while cleaning.

The repair method of shearing machine cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

Answers to some questions about shearing machine cylinder:

How is the cylinder of hydraulic cylinder processed?
As the main parts of hydraulic cylinder, mining single pillar, hydraulic support, gun barrel and other products, its processing quality directly affects the life and reliability of the whole product. Cylinder processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of cylinder is deep hole processing, which has always troubled the processing personnel. Due to the residual compressive stress on the surface of the surface layer, the rolling machining is helpful to seal the small cracks on the surface and prevent the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the cylinder can be improved.

CNC lathe rotary cylinder oil leakage and treatment methods
Oil leakage often occurs when the cylinder (especially the hollow cylinder) of the CNC lathe is installed. First check the cylinder yaw, be sure to reach or close to the required value, generally the cylinder requires the outer beat within 1 wire. Otherwise, too much beating is sure to leak oil. Then check whether the tubing is smoothly downward at a certain Angle, and can not bend. Look at the pipe outlet can not go into the oil level, to a little higher. Otherwise, there's back pressure and it's gonna leak.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
2017午夜福利视频| 国产成人自拍三级片在线观看| 天堂狠狠干| 中文字幕久久无码一区视频| 9久热国产精品视频| 9操逼Av| 春桃久久久久91| 亚洲黄色一级大片| 亚洲日韩欧美在线第一第二| 四虎永久免费熟女| 乱人伦人妻精品一区| 嗯嗯…啊啊啊在线观看| 91爱爱小电影| 美国大屌操骚逼| 淫妻无码在线| 一级国产黄色破处| 亚洲熟女p一区| 合肥市| 无码插小骚逼| 极品香蕉少妇| 丰满尤物久久| 黑人巨屌插美女视频| 屁股人妻欧洲日韩| 逼逼被日好痛视频| 国产又粗又硬又粗又黄的视频| 啊啊啊啊啊啊啊疼视频| 天天操天天添| 原创AV爱色| 一区三区三区九区在线视频| 伊红院成人小视频| 90号精品人妻一区二区三区| 国产激情AV| 色友视频国产| v五码天堂| 丝袜久久久久久久| 青青草原欧美福利在线观看| 日本大香蕉视频插放| 美女搞雞巴| 国内自拍偷拍三级| www、操美女| 三级亚洲欧美人妻|