亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

supporting cylinder Sold to Poland

Release time:2023-11-14 08:41:15 Hits: Current position: Home > News

This article mainly introduces:

Poland hydraulic cylinder,supporting cylinder manufacturer,supporting cylinder

Poland supporting cylinder

(Poland supporting cylinder,produced by Hengyu Hydraulic Cylinder Factory)

supporting cylinder are widely used in Poland,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed supporting cylinder for customers from Poland.

Introduction to supporting cylinder:

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

Factors that should be considered when selecting the oil seal in the supporting cylinder: some specific factors should be taken into account when selecting the oil seal in the supporting cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: supporting cylinder diameter, piston rod diameter, piston rod and piston groove size, supporting cylinder working pressure, supporting cylinder movement speed, hydraulic system oil temperature and supporting cylinder working environment.

Before the supporting cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

The repair method of supporting cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

Answers to some questions about supporting cylinder:

What do cylinder internal leakage and external leakage mean?
Internal leakage means that the piston seal in the cylinder is not strict, there is a leak between the two chambers of the cylinder, the oil is still in the cylinder, and the external leakage is that the oil leaks to the outside of the cylinder.

Need a hydraulic cylinder, vertical upward 10 seconds to lift 20 tons of weight up 2 meters, how large cylinder and rod, how much pressure to use the plunger pump and how big?
The first thing to determine the system pressure, let's say 25 mpa, can take into account cost and performance. 1 Cylinder area 20000/250=80 square cm cylinder diameter (80/3.14) squared x2=200 mm 2 cylinder volume 80x200=16000 ml =16 L 3 Required pump flow 16x60/10=96 L/min 4 Power 96x25/55=43 kW 45 kW motor is available.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
在线 国产 姐姐| 操美国女人的屄| 欧巴美女舔鸡巴| 插逼视频播放入口| 综合AV第一节| 麻豆精品一二三| 超碰小黄片| 无码精品另类视频| 99热国产密臀| 亚洲精品136| 蜜桃av超碰在线| 小姐姐白白日白白操| 国产在线小视频在线播放| 欧美破处日韩一区二区| 大鸡巴操美女国产黄片| 鸡巴插入美女下体视频| 一区二区三区91国产精品视频| 人妻妇伦又伦精品app| 亚洲 欧洲 小说 人妻 偷拍| 日韩欧美系列视频在线观看| 连云港市| 美女操逼视频美女一区二区| 大香蕉日韩A视频V| 操日本一区| 骚货人妻| 好吊操91视频1区2区| 制服丝袜人妻中文字幕| av在线不卡三区| 日本大屌屌女人视频国产| 嗯 啊 用力操啊视频| 好吊妞一区二区这里| 虐逼高潮出水大鸡巴| 超碰在线青青人人| 先锋伦理啪啪| 亚洲熟女人妻激情一区二区三区 | 2024日韩精品成人在线| 犍为县| www.少妇网站| 综合十二月激情网| 亚洲色图淫荡人妻| 逼白虎网站|