亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

supporting cylinder Sold to Czech Republic

Release time:2023-11-14 08:41:16 Hits: Current position: Home > News

This article mainly introduces:

Czech Republic hydraulic cylinder,supporting cylinder manufacturer,supporting cylinder

Czech Republic supporting cylinder

(Czech Republic supporting cylinder,produced by Hengyu Hydraulic Co., Ltd)

supporting cylinder are widely used in Czech Republic,because of no need for deceleration device,high work efficiency,excellent fatigue and impact resistance.So our company has designed supporting cylinder for customers from Czech Republic.

Introduction to supporting cylinder:

The method of sleeve supporting cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the supporting cylinder can be significantly improved by rolling in the finishing of the inner holes of the supporting cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.

When the hydraulic oil is not pumped into the supporting cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the supporting cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

The cavitation of the supporting cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the supporting cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

If the supporting cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

Answers to some questions about supporting cylinder:

Servo cylinder control principle
The electro-hydraulic pulse servo cylinder is composed of a stepper motor, a three-position four-way servo valve, a mechanical feedback device (a wire carrier) and an oil lever. When the stepper motor gets a pulse signal, its output shaft rotates 1.5 or 3 degrees, the servo valve spool drives the wire to rotate at the same time, the valve spool moves and opens the reversing cylinder to output pressure oil, the piston moves and drives the lead screw to reverse rotate the valve spool back to the original position, and the servo valve stops output pressure oil in the center. At this time, the cylinder moves 0.1 or 0.2mm stroke, and the displacement and speed of the cylinder travel are determined according to the given value of the electrical pulse.

How to repair the bent oil cylinder correctly?
If the bending oil cylinder leaks, the most direct way is to replace the seal ring. Most of the sealing rings used by domestic bending machines are made in Taiwan and Japan, so the service life of the sealing ring is still relatively long. If the bending oil cylinder used by the customer leaks oil, then when replacing the seal ring, be sure to choose a high-quality and durable seal ring. In this way, the replaced cylinder will not leak oil for a long time.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩熟妇人要中出| 一区二区免费在线看| 精品在线视频一| 操大胸美女老师大鸡巴| 亚洲精品成人AV一区二区三区| 免费国产传媒高清av在线| 九九国产一区二区| 亭亭色站| 日本一区日逼| 大奶大鸡巴爆操| 大鸡吧日逼网站| 操操操操操日| 欧美日韩精品一区二区天天拍小说| 日本人的插逼逼视频免费看| 校园春色综合| AV片男人的天堂免费观看| 韩国成人三级片在线视频| 熟女五十三区四| 自慰在线精品| 操逼试看视频免费| 亚洲欧洲韩日午夜一线一品| 又色大又硬的视频在线播放| 无码自拍视频视频| chaopeng98无码| 国产三级国产精品国产专区50| 狠色狠色精品中文字幕| 黑人大鸡巴日屄| 蜜桃我操av| 中文字幕成人精品一区| 成人黄性视频| 啊啊啊嗯嗯嗯在线看| 免费福利在线观看| 啊插进去了视频| 激情五月网日本| 亚洲情侣激情视频| 美女日逼视频免费下载| 在线视频观看骚货| 国产精品久久喷水| 亚洲出轨人妻少妇中文| 性情网站在线观看日韩哦| 欧亚美国日本韩国在线观看|