亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo cylinder Sold to Cote d 'Ivoire

Release time:2023-11-27 15:08:49 Hits: Current position: Home > News

This article mainly introduces:

Cote d 'Ivoire hydraulic cylinder,servo cylinder manufacturer,servo cylinder

Cote d 'Ivoire servo cylinder

(Cote d 'Ivoire servo cylinder,produced by Hengyu Hydraulic Co., Ltd)

servo cylinder are widely used in Cote d 'Ivoire,because of long service life,smooth movement,high work efficiency.So our company has designed servo cylinder for customers from Cote d 'Ivoire.

Introduction to servo cylinder:

The servo cylinder should be vented: when the servo cylinder is installed or parked for a long time to work again, the air will penetrate into the servo cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the servo cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the servo cylinder, the oil is best entered and discharged from the highest point of the servo cylinder. servo cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

If the piston rod and servo cylinder are stuck or the servo cylinder is blocked, at this time, no matter how to operate, the servo cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the servo cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

servo cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

servo cylinder can not drive the load troubleshooting: oil pressure is too low. servo cylinder selection specifications are too small. Leakage in servo cylinder or associated hydraulic system element.

Answers to some questions about servo cylinder:

How to deal with the surface degreasing process before spraying paint after cylinder assembly, and what degreasing agent is used?
Cylinder painting, generally using the following process (note: the cylinder is best painted, do not spray powder coating, because the powder coating curing temperature is high, will lead to sealing defects and oil leakage) : Pre-degreasing - degreasing - washing - washing - pickling - washing - washing - table adjustment - phosphating - washing - washing - drying - polishing - spray primer - spray paint degreasing agent generally use neutral or weak alkaline degreasing agent, phosphating liquid generally use zinc phosphating liquid.

How to select swing cylinder? Under what conditions are they designed and selected?
1, determine the system parameters: ① the weight and the required force; ② Nominal working pressure and range; ③ The time required to travel this distance; 4 oil medium 2, installation method: select the appropriate way for the specific application 3, cylinder diameter and working pressure: determine the cylinder diameter and provide the necessary force required by the system pressure 4, piston rod: determine the minimum piston rod diameter required to withstand the longitudinal bending force, select the appropriate piston rod end and piston rod end thread 5, piston: Whether the seal type is suitable for the application 6, buffer: choose the buffer requirements as appropriate.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲色欲色欲综合网站| 天天操天天爱天天爽| 久久久久人体艺术蜜桃| 大鸡吧抽插去干网| 亚洲成人我不卡| 操美女视频在线播放| 91大神沈先生在线播放| 光棍的日B视频| 久久av不卡人妻出轨一区二区| 字幕女女蕾丝边一区二区三区| 少妇被领导玩呻吟声太大| 丝袜91人妻内射| 鸡巴骚穴在线播放| 国产欧美精品xxxx另类| 1024骚逼| 俄罗斯逼片| 国产无遮挡啪啪啪| 亚洲成人精品av| 操烂你小逼操出白浆视频| 男人狠狠干视频| 美女内射免费视频| 色日本在线播放| 木下凛凛子亚洲无码| 91aV一区二区在线| 亚洲少妇啪啪| 中文乱码人妻系列一区二区| 五月妞婷婷操逼| 高清女厕偷拍一区二区三区| 永登县| 婷婷热一区二区| 中文字幕蜜臀av一区二区| 午夜诱惑av| 色哟哟网站在线观看入| 日韩国产丝袜久久| 360浏览器欧美一级色| 熟妇色操日本SSS| 国产美女网站大全免费观看视频| 日本三二一在线| 五十路操碰| 日韩在线无| 久久精品国产人伦|