亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

single rack cylinder Sold to Oman

Release time:2023-11-27 15:08:50 Hits: Current position: Home > News

This article mainly introduces:

Oman hydraulic cylinder,single rack cylinder manufacturer,single rack cylinder

Oman single rack cylinder

(Oman single rack cylinder,produced by Hengyu Hydraulic Cylinder Factory)

single rack cylinder are widely used in Oman,because of no need for deceleration device,long service life,smooth movement.So our company has designed single rack cylinder for customers from Oman.

Introduction to single rack cylinder:

When the single rack cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the single rack cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil single rack cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical single rack cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the single rack cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the single rack cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

If the single rack cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

If the piston rod and single rack cylinder are stuck or the single rack cylinder is blocked, at this time, no matter how to operate, the single rack cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the single rack cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Answers to some questions about single rack cylinder:

What components can control cylinder rising and falling speed and the speed is adjustable?
A throttle or special solenoid valve is required. The reversing valve can choose the three-position reversing valve with P-type middle function. When rising, the reversing valve can be changed to the middle position to achieve differential connection and the fastest speed. Add a combination valve one-way throttle valve in the oil return circuit, connection mode: when the cylinder rises, the oil flows back to the tank through the check valve, the throttle valve is reversed off, when the cylinder falls, the reversing valve is changed to the left or right position (see the structure of the valve), the check valve is reversed off, the oil returns to the tank through the throttle valve, and the speed can be adjusted through the throttle valve.

What parameters do I need to provide when purchasing hydraulic cylinders?
The main technical parameters of the hydraulic cylinder: 1. Cylinder diameter; Cylinder diameter, inner diameter size; 2. Piston rod diameter; 3. Cylinder stroke; 4. Cylinder pressure; The working pressure of the cylinder is often calculated using the test pressure, which is less than 16MPa multiplied by 1.5 and higher than 16 multiplied by 1.255. Import and export diameter and thread parameters; 6. Whether there is buffer; According to the working conditions, the piston rod extension contraction is generally buffered if the impact is large. 7. Installation method of oil cylinder, etc.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
肉棒av网站| 男人 伸进 视频白丝| 色诱久久综合| 日本加勒比久久综合88| 美女让人捅到爽| 国产一区二区’| 操逼操逼操逼日本操逼片| 91大神长腿精品在线观看| 有俄罗斯免费操逼视频吗| 艹逼网站视频嗯啊嗯操| 熟妇日本亚洲欧美色| 欧美视频自拍区| 黑人性生活免费视频| 中文字幕蜜臀av一区二区| 欧日中文字幕一区二区| 老司机 日韩 视频一区| 日本中文 第一页| 十区十一区淫视频| 人妻熟女一区精品久| 抽插白虎美女逼| 国产淫妇av| 99国内性爱网| ′亚州熟妇色| 超碰在线三级片| 嗯…啊鸡巴在线播放av| 大鸡巴操屄亚洲精品| 免费三级中文字幕| 操AV九色| 午夜国产男女视频| 久热333| 少妇人妻女…果太紧了A片91天美 捅美女鸡鸡免费视频网站 | 国产精品三级专区av| 欧美日韩快干烂我的逼逼| 婷婷操五月| 天堂成人精品| 鸡逼精品| 老司机视频91精品三区| 亚洲插日韩av免费观看| 天天舔天天日天天| 国产+日韩+欧美在线观看视频| 亚洲欧美日韩高清另类在线观看|