亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

vehicle hydraulic cylinder Sold to El Salvador

Release time:2023-11-08 15:23:28 Hits: Current position: Home > News

This article mainly introduces:

El Salvador hydraulic cylinder,vehicle hydraulic cylinder manufacturer,vehicle hydraulic cylinder

El Salvador vehicle hydraulic cylinder

(El Salvador vehicle hydraulic cylinder,produced by Hebei Hengyu company)

vehicle hydraulic cylinder are widely used in El Salvador,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed vehicle hydraulic cylinder for customers from El Salvador.

Introduction to vehicle hydraulic cylinder:

When the vehicle hydraulic cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the vehicle hydraulic cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the vehicle hydraulic cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the vehicle hydraulic cylinder can meet the requirements by grinding. However, the life and reliability of this repair vehicle hydraulic cylinder are not high.

The internal leakage of the vehicle hydraulic cylinder should be prevented when the vehicle hydraulic cylinder is used. The internal leakage of vehicle hydraulic cylinder includes the leakage caused by excessive wear of vehicle hydraulic cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the vehicle hydraulic cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

The vehicle hydraulic cylinder is not the same as the vehicle hydraulic cylinder, because the pressure of the pneumatic system is generally within the range of 0.2-1.0Mpa, the vehicle hydraulic cylinder can not be used as a high-power power component, but the vehicle hydraulic cylinder can be used as a relatively large power component, or the vehicle hydraulic cylinder system can be used.

Answers to some questions about vehicle hydraulic cylinder:

How to calculate cylinder pressure?
Hydraulic pressure area of cylinder × hydraulic pressure = output force of cylinder 200mm=20cm 100mm=10cm 15Mpa=150Kg/cm2 Cylinder thrust: 3.14×10×10 area ×150 pressure =47100Kg=47.1t cylinder pulling force: 3.14×(10×10-5×5) Area ×150 pressure =35325Kg=35.325t The above calculation did not consider the resistance of oil return, because you did not provide oil return pressure. But the impact should be small.

What welding rod is used for hydraulic cylinder welding?
There are several reasons for bad welding of hydraulic cylinder: 1. There is hydraulic oil on the welding surface, wipe it with a rag, there will be bubbles in the welding process, and it will not last for a few days. You have to remove it, drain it, wash it off with gasoline and try again. 2. Open the groove before welding, it is not deep enough to use the Angle grinding machine, and can not find the accurate crack position. 3. The material of the cylinder itself is not clear, the welding performance of more than 35 steel is not good, in the factory welding needs to preheat, the welding rod should also be dried and insulated, there is no such condition on the site.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日本又粗又大又黄一区二区精品| 高清福利在线| 91n免费处女在线破视频+进...| 美女被暴操网| 日一小少妇二区| 操美女靠逼的美女| 亚洲欧美在线青青| 大鸡巴总裁操逼视频| 红桃网站AV| 精品人妻观看| 91视频一区二区三区视频精品| 一本清道一区二区| 色666站| 日韩成人精品一卡二卡三| www.xx日本大香蕉| 欧洲美女视频网站| 鸡巴插入美女下体视频| 操死你精品在线| 一道夫成人AV| 青娱乐啊v在线中文字幕| 男女日比比| 逼逼射射视频| 国产操B视频一区二区三区 | 日逼综合| 鸡巴插之逼视频| 丁香七月啪| 91大神未删减在线观看| 女生扒开逼让男生捅| 国产一级色片| 激情狠狠的插| av操b女| 欧美日韩字幕****综合另类| 内射少妇穴| 中文字幕偷拍熟| 啊啊啊嗯嗯在线免费观看视频| 鸡巴久久久久久久狂操| 东京热HD18| 操大屌 操操操| 亚洲无码一区二区三区影视| 不卡无在线一区二区三区免费视频| 男人操美女逼视频无遮挡网站|