亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailboard balance cylinder Sold to Nigeria

Release time:2023-11-08 15:23:30 Hits: Current position: Home > News

This article mainly introduces:

Nigeria hydraulic cylinder,tailboard balance cylinder manufacturer,tailboard balance cylinder

Nigeria tailboard balance cylinder

(Nigeria tailboard balance cylinder,produced by Hengyu Hydraulic Cylinder Factory)

tailboard balance cylinder are widely used in Nigeria,because of no need for deceleration device,long service life,smooth movement.So our company has designed tailboard balance cylinder for customers from Nigeria.

Introduction to tailboard balance cylinder:

The wear of the hard chromium plating layer of the tailboard balance cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

When the tailboard balance cylinder is customized, if there are high requirements for the quality of the tailboard balance cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the tailboard balance cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the tailboard balance cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

Piston tailboard balance cylinder is widely used in hydraulic transmission. When the tailboard balance cylinder works, it mainly delivers hydraulic oil alternately to both sides of the piston in the tailboard balance cylinder, and uses the pressure difference of hydraulic oil on both sides of the piston to realize the reciprocating movement of the piston. If you want to speed up the forward speed of the piston, the return oil in the tailboard balance cylinder can be controlled by the valve and directly input into the inlet pipe to participate in the work of the piston to achieve rapid movement of the piston, but the thrust of the piston is reduced much.

Do not regularly check the damage of the chrome layer of the tailboard balance cylinder: completely extend the tailboard balance cylinder and carefully check whether there is any surface damage such as injury, strain, welding slag, such as the surface damage position, in the tailboard balance cylinder block < 20cm, and the damage depth < 5mm, should be repaired in time to prevent long-term damage to the tailboard balance cylinder seal. Welding slag is strictly prohibited on the surface of the tailboard balance cylinder.

Answers to some questions about tailboard balance cylinder:

How to disassemble the big nut that excavate the oil cylinder piston of the excavator?
If you want to be safe, look for a special unloading place for this thing, which is an oil cylinder on top of a turntable with a large nut attached to the center of the turntable. If you're in the field just pin the head of the cylinder to one end, use a big homemade wrench to hold the nut in place, and then get a digging machine and push it down, and it opens.

Why manual forklift oil cylinder can not lift up?
Manual hydraulic forklift truck often can not be pressed up, there are several reasons: for manual hydraulic truck: 1) There is no hydraulic oil 2) the purity of the oil is not enough 3) the adjusting bolt is too close or the adjusting screw is too tight, so that the valve is always open, 4) there is an air in the hydraulic cylinder. Method: 1) Refueling 2) Oil change 3) air discharge. For manual hydraulic stacker, also called manual lift car 1) Less than the amount of oil 2) impurities in the hydraulic oil, so that the check valve can not be closed. Method 1) Add enough hydraulic oil 2) Remove the cylinder, screw off the bottom plate, remove the impurities in the bottom plate.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
福利国产av| www.国产一区二区三区.com| 少妇被粗大的猛进进出出免费观看| 中文精品字幕一区二区| 嗯嗯啊,啊免费观看视频| 日本三二一在线| 成人午夜性爱福利网站| 真人操逼视频网站负费欧美| 97在线公开视频| 我要大鸡吧操我视频在线播放| 韩国av一区二区| 99操逼啊| 91丨九色丨国产丨人妻一区二区三区| 激情高潮抽插视频| 青春草手机在线免费视频| 福鼎市| 白嫩少妇人妻| 肛交免费视频久久精品| 嗯~啊~草| 亚洲欧美日韩国产一区二区三区| 男生操女生的视频免费观看| 中国农村老熟女2| 国产丰满熟女操| 美洲精品一二三区| 大鸡吧操的我小骚逼好爽视频| 美女操爽鸡巴| 98好吊妞在线视频| 亚洲男人天堂av一区| 林由奈无码av免费一区| 日逼操穴免费观看视频| oumei88av| 中文字幕在线电影一二三区| 在线播放爆插白虎| 一级A A网站| 亚洲国产有码无码四区| 91爱爱男人的天堂| 人妻一级黄色片| 不卡9区| 在线视频嗯| 长硬的鸡巴插入小穴视频在线播放| kaobi视频|