亚洲色图10p,久久婷婷五月综合色欧美蜜芽,成人毛片无码一区二区三区,亚洲成av人在线视

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailboard balance cylinder Sold to Estonia

Release time:2023-11-08 15:23:30 Hits: Current position: Home > News

This article mainly introduces:

Estonia hydraulic cylinder,tailboard balance cylinder manufacturer,tailboard balance cylinder

Estonia tailboard balance cylinder

(Estonia tailboard balance cylinder,produced by Hengyu Hydraulic Co., Ltd)

tailboard balance cylinder are widely used in Estonia,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed tailboard balance cylinder for customers from Estonia.

Introduction to tailboard balance cylinder:

The piston seal of the tailboard balance cylinder is the main element to prevent leakage in the tailboard balance cylinder. For the lip seal, it should focus on checking whether the lip edge is bruised and worn, and for the combination seal, it should focus on checking the wear of the sealing surface, and then determine whether the seal can be used. In addition, it is necessary to check whether the static seal between the piston and the piston rod is crushed. The piston rod seal should focus on checking the wear of the seals and supporting rings.

tailboard balance cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

When the tailboard balance cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the tailboard balance cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the tailboard balance cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

The viscosity of the working oil used in the tailboard balance cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

Answers to some questions about tailboard balance cylinder:

Is there a way to make the cylinder stop pushing when it hits something hard during the process of pushing?
The simplest solution is to press the stop switch, this switch has a mechanical type, touch the object on the action or send a stop signal, through the operation of the motor control cylinder; There is also an induction switch, that is, when the hydraulic cylinder expands to the range of the induction switch can sense the signal, it sends a signal to let the motor act, resulting in the corresponding action of the cylinder.

Why hydraulic cylinder load can not rise?
The hydraulic cylinder does not top up indicates that the pressure of the working chamber of the hydraulic cylinder is insufficient, and the following circumstances can lead to insufficient pressure: 1) The relief valve of the hydraulic system cannot establish pressure, elimination method: check whether the pressure setting screw of the relief valve is screwed to the appropriate position. If it is an electromagnetic relief valve, please check the power-on condition. 2) The hydraulic system pipeline is connected incorrectly, when P and T are connected, this must be checked and excluded; 3) Excessive leakage in the hydraulic cylinder, resulting in (only for double-acting cylinders); 3) No hydraulic oil into the working chamber of the hydraulic cylinder, elimination method: first disassemble the hydraulic pipe connecting the reversing valve and the hydraulic cylinder, and then control the reversing valve, and observe whether there is hydraulic oil flowing out of the reversing valve.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
操骚逼操虎逼| 马鞍山市| 艹B动图久久网| 老司机超碰| 午夜福利视频你懂的| 国产激情国产视频又长又粗大| 成人 蜜桃 一区| 扒开老女人bb欧美日韩| 大屌轮奸日韩无码| 激情片a一区| 亚洲日韩国产欧洲久久木下| 日本韩国香蕉成人视频| 欧美日一级| 亚洲美妇天堂| 精品二区三区在线91| 久热久本道淫久| 在线播放人妻轮奸中出| 亚洲熟女人妻AV| 色逼AV一区| 鸡巴插小穴视频无码| 欧洲色欧美亚洲另类二区不卡| 人人操色播基地| 人妻岛国高清一区二区| 外国美女双人互相舔鸡网站| 中文字幕有码中文字幕无| 懂色中文| 黑人一极片视频呢| 欧美B 高潮喷水视频| 亚洲激情啪啪啪永久精品| 人妻一区15p| 色哟哟无码进入| 啊啊啊大鸡巴 国产精品| 污视频网址欧美| 日韩AP 久久久| 日韩av片| 日逼骚片| 妹妹自拍一区| dashen91com| 伦理在线 一区二| 91精品人妖一区二区三区四区| 欧美日韩ab|